Read Harman Kardon TU 950 (serv.man4) User Guide / Operation Manual online
ENGLISH
1. POWER BUTTON
Press this button to turn the unit on.
Press it again to turn the unit off. Note
that the rings above and below the
button will glow green when the unit
is on.
Press it again to turn the unit off. Note
that the rings above and below the
button will glow green when the unit
is on.
2. DISPLAY BUTTON
Pressing this button will display
information about the current
frequency or station. Each press of
the button will cycle the display to the
next item in the sequence. The
information available will vary with the
band in use and the availability of
RDS information.
information about the current
frequency or station. Each press of
the button will cycle the display to the
next item in the sequence. The
information available will vary with the
band in use and the availability of
RDS information.
a) Display for FM stations when RDS
is turned on:
Note: Due to the nature of RDS
transmissions, the unit needs to be
tuned to a station for a short period
before the time display will appear.
This is normal and does not indicate a
fault with either the unit or broadcast
station.
transmissions, the unit needs to be
tuned to a station for a short period
before the time display will appear.
This is normal and does not indicate a
fault with either the unit or broadcast
station.
b) Display for FM station when RDS
is turned off:
c) Display for MW or LW:
3. MEMORY BUTTON
This button is used to enter stations
into the preset memories. The
memory indicator blinks when the
button is pressed.
See page 9 for instructions on using
the memory system.
into the preset memories. The
memory indicator blinks when the
button is pressed.
See page 9 for instructions on using
the memory system.
4. RDS BUTTON
Pressing this button once turns on
the RDS system for FM broadcasts
and is confirmed by illumination of
the RDS indicator on the display
panel. When the unit is in the RDS
mode and is tuned to a station
transmitting RDS data, the station’s
frequency will be shown briefly and
the display will then switch to the call
letters or other identifying information
contained in the RDS data signal.
When no signals are available with
RDS data, the display will indicate
“NO RDS”.
Pressing this button twice, or until the
RDS and TP indicators light up
activates the RDS Traffic Program.
When in this mode, the tuner will
display RDS data if it is transmitted,
as well as special traffic advisories
when available.
the RDS system for FM broadcasts
and is confirmed by illumination of
the RDS indicator on the display
panel. When the unit is in the RDS
mode and is tuned to a station
transmitting RDS data, the station’s
frequency will be shown briefly and
the display will then switch to the call
letters or other identifying information
contained in the RDS data signal.
When no signals are available with
RDS data, the display will indicate
“NO RDS”.
Pressing this button twice, or until the
RDS and TP indicators light up
activates the RDS Traffic Program.
When in this mode, the tuner will
display RDS data if it is transmitted,
as well as special traffic advisories
when available.
5. AF BUTTON
Pressing this button when the RDS
system is turned on and RDS data is
present will cause the tuner to
automatically scan up to six
alternative frequencies for the same
network or service tuned. It will then
select the frequency that offers the
system is turned on and RDS data is
present will cause the tuner to
automatically scan up to six
alternative frequencies for the same
network or service tuned. It will then
select the frequency that offers the
best reception. If no list of alternate
frequencies are available, the tuner
will display a “NO AF” message. This
feature is particularly useful when
listening to national radio networks
where the same program is broadcast
on a number of transmitters.
frequencies are available, the tuner
will display a “NO AF” message. This
feature is particularly useful when
listening to national radio networks
where the same program is broadcast
on a number of transmitters.
6. PTY BUTTON
Press this button to select a particular
PTY (Programme Type) according to
the information transmitted by an RDS
station. After pressing PTY, turn the
Tuning Knob (#8) to select from one
of the following programme types:
PTY (Programme Type) according to
the information transmitted by an RDS
station. After pressing PTY, turn the
Tuning Knob (#8) to select from one
of the following programme types:
•
NEWS
•
AFFAIRS: Political and current
events
events
•
INFO: General information,
financial and trading news,
medical conference and weather
information
financial and trading news,
medical conference and weather
information
•
SPORT: Sporting events
•
EDUCATE: Scholastic and
industrial education programmes
industrial education programmes
•
DRAMA: Broadcast plays and
literature performances
literature performances
•
CULTURE: Cultural, religion and
community programmes
community programmes
•
SCIENCE: Scientific and technical
programmes
programmes
•
VARIED: Entertainment
•
POP M: Popular music
•
ROCK M: Rock music
•
M O R: Middle of the Road Music
•
LIGHT M: Light Classical Music
•
CLASSICS: Serious Classical
Music
Music
•
OTHER M: Other types of musical
programmes, i.e. Jazz, Reggae,
Rap, etc.
programmes, i.e. Jazz, Reggae,
Rap, etc.
•
ALARM
After selecting a programme choice,
press the PTY button again to begin
the search. The unit will scan all RDS
stations and tune to the station with
the strongest signal transmitting the
selected programme type. If no
station with the selected programme
type is available in your area, the
display will show NO PTY and return
to the previous station.
press the PTY button again to begin
the search. The unit will scan all RDS
stations and tune to the station with
the strongest signal transmitting the
selected programme type. If no
station with the selected programme
type is available in your area, the
display will show NO PTY and return
to the previous station.
7. CHARACTER BUTTON
This button enables the system which
permits you to enter or modify the
name of any FM, LW or MW station
which is not broadcasting in RDS.
To enter a name, press the
CHARACTER button once and
observe that a line will flash under the
first digit of the display.
permits you to enter or modify the
name of any FM, LW or MW station
which is not broadcasting in RDS.
To enter a name, press the
CHARACTER button once and
observe that a line will flash under the
first digit of the display.
Turn the tuning knob until the desired
letter, number or symbol appears.
Press the button again to advance to
the next digit. Repeat the procedure
for all places in the display, using the
tuning knob to select a character and
letter, number or symbol appears.
Press the button again to advance to
the next digit. Repeat the procedure
for all places in the display, using the
tuning knob to select a character and
4
Front Panel Controls and Displays
Frequency
(in Frequency Mode)
Signal Level
PS name
Program type
Program No. (in Preset Mode)
Clock / Time (24 hour system)
Frequency
(in Frequency Mode)
Signal Level
Station name
Program No. (in Preset Mode)
Frequency
Station name
STEREO
FM
TU950 230V-eng 11/01/98 15:18 Side 4
Click on the first or last page to see other TU 950 (serv.man4) service manuals if exist.