Read Harman Kardon SB 30 (serv.man2) EMC - CB Certificate online
Report No:W-N-1109009-CY-01-1
Telecom Technology Center
37
6.7 ELECTROSTATIC DISCHARGE
st Sp
rd:
IEC 61000-4-2
6.7.1 Te
ecification
Basic Standa
Discharge Impedance:
330 ohm / 150 pF
Discharge Voltage:
Air Discharge:2kV/4kV/8 Kv (Direct)
Contact Discharge:2kV/4kV (Direct/Indirect)
Contact Discharge:2kV/4kV (Direct/Indirect)
Polarity:
Positive & Negative
Number of Discharge:
Air Discharge: min. 10 times at each test point
Contact Discharge: min. 25 times at each test point
Contact Discharge: min. 25 times at each test point
Discharge Mode:
Single Discharge
Discharge Period:
1 second minimum
6.7.2 Test Procedure
he test generator necessary to perform direct and indirect application of discharges
the EUT in the following manner:
. Contact discharge was applied to conductive surfaces and coupling planes of the
UT.
t
th single discharges. For the single discharge
suc
le discharges was at least 1 second. The EUT shall be
to a
discharges, 100 each at negative and positive polarity, at a
st points shall be subjected to at least 50
er of the front edge of the horizontal coupling plane.
receive at least 50 direct contact
discharges.
If no direct contact test points are available, then at least 200 indirect discharges
shall be applied in the indirect mode. Test shall be performed at a maximum
repetition rate of one discharge per second.
The selected point, which was performed with electrostatic discharge, please
refers to the “Photo(s) shown the location(s) of ESD evaluated”.
Vertical Coupling Plane (VCP):
The coupling plane, of dimensions 0.5m x 0.5m, is placed parallel to, and
positioned at a distance 0.1m from, the EUT, with the Discharge Electrode
touching the coupling plane.
The four faces of the EUT will be performed with electrostatic discharge.
Horizontal Coupling Plane (HCP):
The coupling plane is placed under to the EUT. The generator shall be positioned
vertically at a distance of 0.1m from the EUT, with the Discharge Electrode
touching the coupling plane. The four faces of the EUT will be performed with
electrostatic discharge.
If no direct contact test points are available, then at least 200 indirect discharges
shall be applied in the indirect mode. Test shall be performed at a maximum
repetition rate of one discharge per second.
The selected point, which was performed with electrostatic discharge, please
refers to the “Photo(s) shown the location(s) of ESD evaluated”.
Vertical Coupling Plane (VCP):
The coupling plane, of dimensions 0.5m x 0.5m, is placed parallel to, and
positioned at a distance 0.1m from, the EUT, with the Discharge Electrode
touching the coupling plane.
The four faces of the EUT will be performed with electrostatic discharge.
Horizontal Coupling Plane (HCP):
The coupling plane is placed under to the EUT. The generator shall be positioned
vertically at a distance of 0.1m from the EUT, with the Discharge Electrode
touching the coupling plane. The four faces of the EUT will be performed with
electrostatic discharge.
b. Air discharges at insulation surfaces of the EUT.
It was at least ten single discharges with positive and negative at the same selected
point.
point.
c. For the actual test configuration, please refer to the related Item –EUT Test Photos.
T
to
a
E
to
a
E
During the est, it was performed wi
time
between
time
between
cessive sing
exposed
minimum of four test points. One of the te
minimum of four test points. One of the te
t least 200
indirect discharges to the cent
The remaining three test points shall each
The remaining three test points shall each
Click on the first or last page to see other SB 30 (serv.man2) service manuals if exist.