Read Harman Kardon SB 26 (serv.man3) EMC - CB Certificate online
Page 3 of 40
Report No.: ACSCBAV13004
TRF No. IEC60065K
List of Attachments (including a total number of pages in each attachment):
-
Attachment 1: European Group Differences (15 pages)
-
Attachment 2: National Deviations: Australia/New Zealand, Korea, MALAYSIA, Japan (15 pages)
-
Attachment 3: Manufacturer’s Declaration (2 pages)
-
Attachment 4: Photographs (14 pages)
-
Attachment 5: Diagrams (4 pages)
-
Attachment 6: Schematics + PWB Layout (5 pages)
Summary of testing:
1) The sample tested complies with the requirements of the test specification.
2) Soundbar (SB26 CNTR) and Subwoofer (SB26 SUB) were evaluated respectively.
3) As for Power Transformer (T541), multi factories will produce them as alternative use. Since it was
same to each other on construction and electrical characteristics, the difference of factory did not
affect safety aspects.
Unless otherwise specified, all tests were conducted on the following transformer as representative.
T541: Huizhou Sunshine Electronics Co., Ltd. / BCK-AL140
affect safety aspects.
Unless otherwise specified, all tests were conducted on the following transformer as representative.
T541: Huizhou Sunshine Electronics Co., Ltd. / BCK-AL140
4) Following symbols and abbreviations are used in this test report.
S/C= Short-Circuit
O/C= Open-Circuit
NH= No Hazard Occurred
NFR= No Further Results existed
NB= No breakdown NCD= No component damaged
PCB= Printed Circuit Board
* = Determined by the method specified in Note f to Table 3.
PCB= Printed Circuit Board
* = Determined by the method specified in Note f to Table 3.
Tests performed (name of test and test clause):
Marking durability test (5)
Input test (5.1)
Heating test (7.1)
Touch current (9.1.1)
Withdrawal of mains plug test (9.1.6)
Humidity test (10.2)
Insulation resistance and dielectric strength test
(10.3)
Fault condition test (11.1)
Heating test under fault condition (11.2)
Bump test (12.1.1)
Vibration test (12.1.2)
Impact test (12.1.3)
Stress relief test (12.1.5)
Determination of operating voltage (13.2)
Screw securement test (17.1)
Stability test (19.1)
Vertical force stability (19.2)
Wall or ceiling mounting means test (19.6)
Marking durability test (5)
Input test (5.1)
Heating test (7.1)
Touch current (9.1.1)
Withdrawal of mains plug test (9.1.6)
Humidity test (10.2)
Insulation resistance and dielectric strength test
(10.3)
Fault condition test (11.1)
Heating test under fault condition (11.2)
Bump test (12.1.1)
Vibration test (12.1.2)
Impact test (12.1.3)
Stress relief test (12.1.5)
Determination of operating voltage (13.2)
Screw securement test (17.1)
Stability test (19.1)
Vertical force stability (19.2)
Wall or ceiling mounting means test (19.6)
Testing location: see page 2 (Testing procedure
and testing location)
and testing location)
Summary of compliance with National Differences
List of countries addressed: EU, AU, NZ, KR, MY, JP
List of countries addressed: EU, AU, NZ, KR, MY, JP
SG (no national differences in CB-Bulletin)
The product fulfils the requirements of _ IEC 60065: 2001 (Seventh Edition) + A1: 2005 + A2: 2010/
EN 60065: 2002 (Seventh Edition) + A1: 2006 + A11: 2008 + A2: 2010 + A12: 2011_
Click on the first or last page to see other SB 26 (serv.man3) service manuals if exist.