Read Harman Kardon GO PLAY WIRELESS (serv.man7) Service Manual online
4
GO + PLAY WIRELESS
HARMAN KARDON
Bluetooth Pairing and
Technical Specifications
Listening to Audio from a Bluetooth-Capable Device
1. Press the Harman Kardon Go + Play Wireless’s “Power” button. The Status LED will illuminate white.
2. The Harman Kardon Go + Play Wireless unit will automatically enter the Bluetooth pairing mode.
3. Perform a new device search on your Bluetooth-capable device.
4. Select “GO+PLAY WIRELESS” on the device’s pairing list. If the device asks for a passcode,
2. The Harman Kardon Go + Play Wireless unit will automatically enter the Bluetooth pairing mode.
3. Perform a new device search on your Bluetooth-capable device.
4. Select “GO+PLAY WIRELESS” on the device’s pairing list. If the device asks for a passcode,
enter 0000.
5. When pairing is successful the Harman Kardon Go + Play Wireless’s Status LED will change
to blue.
6. Control playback from your Bluetooth-capable device.
To pair with a different device, press and hold the Power button until the LED turns white, then
repeat steps 3 – 5 above.
repeat steps 3 – 5 above.
Listening to Music from an Auxiliary Device
1. Connect the auxiliary device’s output into the “Aux in” jack by using a stereo 3.5mm (1/8"
auxiliary cable (not supplied).
2. Press the “Power” button located on top of the Harman Kardon Go + Play Wireless system
to turn on the unit.
3. Control music playback through the auxiliary device.
4. Adjust volume using the Volume Up (“+”) and Volume Down (“–”) buttons located on top of
4. Adjust volume using the Volume Up (“+”) and Volume Down (“–”) buttons located on top of
the unit.
Charging Your iPhone/iPod
1. Use the cable that came with your iPad, iPhone or iPod to connect it to the rear USB port
of the Go+Play Wireless. (The rubber landing area on top of your Go+Play Wireless is the
perfect place for resting your iPhone or iPod while charging.)
perfect place for resting your iPhone or iPod while charging.)
2. Make sure that the Harman Kardon Go + Play Wireless unit is connected to a live electrical
outlet. Note: The Harman Kardon Go + Play Wireless system will not charge other devices.
3. The Harman Kardon Go + Play Wireless unit will not charge an iPhone/iPod device while
running on battery power.
Technical Specifications
Model:
Harman Kardon Go + Play
™
Wireless
Optional batteries for unit:
8 type D alkaline batteries
Drivers:
Two Ridge and two Atlas transducers
Power:
Tweeters: 2 x 15 watts @ 1% THD
Woofers: 2 x 30 watts @ 1% THD
Woofers: 2 x 30 watts @ 1% THD
Frequency response:
40Hz – 20kHz
Input sensitivity (Aux In):
250mV
Bluetooth transmitter frequency range:
2.4GHz – 2.4835GHz
Bluetooth transmitter power:
≤20dBm (EIRP)
Bluetooth transmitter modulation:
GFSK/ /4-DQPSK/8-DPSK
Dimensions:
Length: 20" (500mm)
Width: 9" (230mm)
Height: 9-1/2" (240mm)
Width: 9" (230mm)
Height: 9-1/2" (240mm)
Weight:
9.4 lb (4.3kg)
Input impedance:
>10k ohms
Signal-to-noise ratio:
>85dB
External power supply
Input voltage: 100 – 240V AC
Output voltage: 18VDC @ 3.6A
Output voltage: 18VDC @ 3.6A
Power consumption:
65W (maximum); 0.5W (standby mode)
HARMAN International hereby declares that this equipment is in compliance with the essential requirements
and other relevant provisions of Directive 1999/5/EC, ErP 2009/125/EC Directive and RoHS 2011/65/EU
Directive. The declaration of conformity may be consulted in the support section of our Web site, accessible
from www.harmankardon.com
and other relevant provisions of Directive 1999/5/EC, ErP 2009/125/EC Directive and RoHS 2011/65/EU
Directive. The declaration of conformity may be consulted in the support section of our Web site, accessible
from www.harmankardon.com
harman/kardon
Go+Play Wireless Service Manual
Page 6 of 21
Click on the first or last page to see other GO PLAY WIRELESS (serv.man7) service manuals if exist.