Read Harman Kardon GO PLAY MICRO (serv.man2) EMC - CB Certificate online
ATTACHMENT
National Differences
Page 55 of 58
Report No.:
15039146 001
National Differences
Clause
Requirement
−
Test
Result – Remark
Verdict
IECEE CB Bulletin on 2007-08-08
US National Differences
3.2.3
Permanent connection of equipment to the mains
supply by a power supply cord is not permitted,
except for certain equipment, such as ATMs.
supply by a power supply cord is not permitted,
except for certain equipment, such as ATMs.
N/A
3.2.5
Power supply cords are required to be no longer
than 4.5 m in length and minimum length shall be
1.5 m. Flexible power supply cords are required to
be compatible with Article 400 of the NEC.
than 4.5 m in length and minimum length shall be
1.5 m. Flexible power supply cords are required to
be compatible with Article 400 of the NEC.
N/A
3.2.9
Permanently connected equipment must have a
suitable wiring compartment and wire bending
space.
suitable wiring compartment and wire bending
space.
N/A
3.3.3
Wire binding screws are not permitted to attach
conductors larger than 10 AWG (5.3 mm
conductors larger than 10 AWG (5.3 mm
2
).
N/A
3.3.4
Terminals for permanent wiring, including
protective earthing terminals, must be suitable for
U.S wire gauge sizes, rated 125 percent of the
equipment rating, and be specially marked when
specified (1.7.7).
protective earthing terminals, must be suitable for
U.S wire gauge sizes, rated 125 percent of the
equipment rating, and be specially marked when
specified (1.7.7).
N/A
3.4.2
Motor control devices are required for cord-
connected equipment with a motor if the
equipment is rated more than 12 A, or if the motor
has a nominal voltage rating greater than 120 V,
or is rated more than 1/3 hp (locked rotor current
over 43 A).
connected equipment with a motor if the
equipment is rated more than 12 A, or if the motor
has a nominal voltage rating greater than 120 V,
or is rated more than 1/3 hp (locked rotor current
over 43 A).
No motor control devices.
N/A
3.4.8
Vertically-mounted disconnect switches and
circuit breakers are required to have the "on"
position indicated by the handle in the up position.
circuit breakers are required to have the "on"
position indicated by the handle in the up position.
No such switches and circuit
breakers.
breakers.
N/A
3.4.11
For computer room applications, equipment with
battery systems capable of supplying 750 VA for
five minutes are required to have a battery
disconnect means that may be connected to the
computer room remote power-off circuit.
battery systems capable of supplying 750 VA for
five minutes are required to have a battery
disconnect means that may be connected to the
computer room remote power-off circuit.
No battery systems.
N/A
4.3.12
The maximum quantity of flammable liquid stored
in equipment is required to comply with NFPA 30.
in equipment is required to comply with NFPA 30.
No flammable liquid.
N/A
4.3.13.5
Equipment with lasers is required to meet the
Code of Federal Regulations 21 CFR 1040.
Code of Federal Regulations 21 CFR 1040.
No Laser.
N/A
4.7
For computer room applications, automated
information storage systems with combustible
media greater than 0.76 m3 (27 cu ft) are
required to have a provision for connection of
either automatic sprinklers or a gaseous agent
extinguishing system with an extended discharge.
information storage systems with combustible
media greater than 0.76 m3 (27 cu ft) are
required to have a provision for connection of
either automatic sprinklers or a gaseous agent
extinguishing system with an extended discharge.
Not automated information
storage systems.
storage systems.
N/A
Click on the first or last page to see other GO PLAY MICRO (serv.man2) service manuals if exist.