DPR 1005 (serv.man2) - Harman Kardon Audio User Guide / Operation Manual. Page 12

12 MAIN REMOTE CONTROL FUNCTIONS

K Tuning Up/Down: When the tuner is in use,
these buttons will tune up or down through the
selected frequency band. If the Tuner Mode
button 

I has been pressed or the Band button

! on the front panel was held pressed so that

AUTO

appears in the Main Information

˜, pressing either of the buttons will

cause the tuner to seek the next station with
acceptable signal strength for quality reception.
When the 

MANUAL

appears in the Main

˜, pressing these

buttons will tune stations in single-step
increments. (See page 43 for more information.)

L OSD Button: Press this button to activate
the On Screen Display (OSD) system used to set
up or adjust the DPR’s parameters.

M Dolby Mode Selector: This button is used
to select one of the available Dolby Surround 
processing modes. Each press of this button will
select one of the Dolby Pro Logic II, Dolby Pro
Logic IIx or Dolby Digital. Note that the Dolby
Digital mode is only available with a digital input
selected and the other modes only as long as a
Dolby Digital source is not playing (except Pro
Logic II with Dolby Digital 2.0 recordings, see
Note on page 7). See page 31 for the available
Dolby surround mode options.

N DTS Digital Mode Selector: When a DTS
source is in use the DPR will select the appropri-
ate mode automatically and no other mode will
be available. Pressing this button will display the
mode currently selected by the DPR´s decoder,
depending on the surround material played and
the speaker setting (see item 

6, page 5). When

a DTS source is not in use, this button has no
function. (See page 25, 31 for the available DTS
options.)

O Logic 7 Selector: Press this button to
select one of the available Logic 7 surround
modes. (See page 31 for the available Logic 7
options.)

P Transport Control Buttons: These but-
tons do not have any functions for the DPR, but
they may be programmed for the forward/reverse
play operation of a wide variety of CD or DVD
players, and audio or video- cassette recorders.
(See page 46 for more information on program-
ming the remote.)

Q Light Button: Press this button to activate
the remote’s built-in backlight for better legibility
of the buttons in a darkened room.

 Skip Up/Down Buttons: These buttons do
not have a direct function with the DPR, but
when used with a compatibly programmed CD or
DVD player/changer they will change the tracks
on the disc currently being played.

 Stereo Mode Selector: Press this button
to select a stereo playback mode. When the but-
ton is pressed so that 

SURR OFF

appears in

the Main Information Display

˜ and only

the SURR. OFF indicators are lit, the DPR will
operate in a bypass mode with true fully analog,
two-channel left/right stereo mode with no sur-
round processing or bass management as
opposed to other modes where digital process-
ing is used. When the button is pressed so that

SURROUND OFF

appears in the Main

˜ and both the DSP

and SURR. OFF indicators are lit, you may enjoy
a two-channel presentation of the sound along
with the benefits of bass management. When
the button is pressed so that 

5 C H STEREO

or 

7 C H STEREO

appears, the stereo signal

is routed to all five speakers, if installed. (See
page 27 for more information on stereo playback
modes).

 DTS Neo:6 Mode Selector: Pressing this
selector button cycles the DPR through the 
various DTS Neo:6 modes, which extract a 
three-, five- or six-channel surround field from
two-channel program material (from PCM source
or analog input signal). The first press selects the
last DTS Neo:6 surround mode that was in use,
and each subsequent press selects the next
mode in the following order:

  Macro Buttons: Press these buttons to
store or recall a “Macro”, which is a pre-pro-
grammed sequence of commands stored in the
remote. (See page 49 for more information on
storing and recalling macros.)

! RDS Select Button: Press this button to
display the various messages that are part of the
RDS data system of the DPR’s tuner. (See page 45
for more information on RDS).

" Preset Up/Down: When the tuner is in
use, press these buttons to scroll through the
stations programmed into the DPR’s memory.
When CD or DVD is selected using the Input
Selector button 

4, these buttons may

function as Slow Fwd/Rev (DVD) or ”+10” (CD,
CDR).

# Clear Button: Press this button to clear
incorrect entries when using the remote to directly
enter a radio station’s frequency.

$ Memory Button: Press this button to enter
a radio station into the DPR’s preset memory. As
soon as the station's frequency starts blinking in
the Main Information Display

˜, you have

five seconds to enter a preset memory location
using the Numeric Keys

H. (See page 43 for

more information.)

% Delay Select Button: This button selects
adjustments to the A/V Sync Delay and the indi-
vidual channel displays. The first press of the but-
ton displays an 

A/V SYNC DELAY

message

in the Lower Display Line

˜ and in the on-

screen display, which means that you may
change the amount of time that all channels are
delayed together behind the video. This enables
you to compensate for the loss of lip sync that
may be caused by digital video processing in
your display or by television stations. To change
the A/V Sync Delay, press the Set Button

F

while the 

A/V SYNC DELAY

message is

visible and then use the 

⁄

/

¤

E to change the setting so that the

sound and the video image are in sync. To
change the delay for an individual output chan-
nel, press the 

⁄

/

¤

E

until the desired channel name is shown, and
then press the Set Button

F. Use the 

⁄

/

¤

E to change the delay

amount. (See page 27 for more information on
delay options.)

& Program Button: This button is used to
begin the process of programming the remote.
Press and hold this button for three seconds to
place the remote in the programming mode.
Once the red LED under the Set Button

F

lights, release the button. You may then select
from the desired option. (See pages 46-48 for
more information on configuring the remote.)

' Speaker Select: Press this button to begin
the process of configuring the DPR’s Bass
Management System for use with the type of
speakers used in your system. Once the button
has been pressed, use the 

⁄

/

¤

buttons 

E to

select the channel you wish to set up. Press the
Set Button

F and then select the speaker

type (Large, Small or None) appropriate with the
speaker in use. (See page 21 for more informa-
tion.)

( Multi-Room: Press this button to activate
the Multiroom system or to begin the process of
changing the input or volume level for the sec-
ond zone. (See page 42 for more information on
the Multiroom system.)

)Volume Up/Down: Press these buttons to
raise or lower the system volume.

DTS Neo:6 MUSIC

DTS Neo:6 
MOVIES