Read Harman Kardon AVR 80MK II (serv.man4) User Guide / Operation Manual online
Front Panel Controls
1
Fluorescent display:
This dis-
play delivers messages and status
indications to help you operate the
receiver. Refer to the separate dia-
gram for complete explanation of the
FL display.
indications to help you operate the
receiver. Refer to the separate dia-
gram for complete explanation of the
FL display.
2
Remote Sensor Window:
The
sensor behind this window receives
infrared signals from the remote con-
trol. Aim the remote at this area and
do not block or cover it unless an
external remote sensor is installed.
infrared signals from the remote con-
trol. Aim the remote at this area and
do not block or cover it unless an
external remote sensor is installed.
3
AM/FM Tuner Mode Selection:
Press this button once to select the
tuner. Press it again to switch
between AM and FM.
tuner. Press it again to switch
between AM and FM.
4
CD:
Press this button to select
the CD player.
5
Tape1/ Monitor:
Press this button
to select Tape One as the input
source. A red LED above the button
will illuminate to indicate that the
Tape Monitor has been selected.
source. A red LED above the button
will illuminate to indicate that the
Tape Monitor has been selected.
6
Tape 2:
Press this button to select
Tape 2.
7
Video Sources:
Press any of
these buttons to select a video input
source.
source.
8
Aux:
Press this button to select
the source connected to the front
panel
panel
Aux
jacks.
9
Multiroom Audio Select:
Press
this button to turn on the feed to the
remote zone. The remote zone will
stay on after the main power switch
is tuned off until it is switched off by
the remote room control or by press-
ing this button again.
remote zone. The remote zone will
stay on after the main power switch
is tuned off until it is switched off by
the remote room control or by press-
ing this button again.
)
Display:
Press this button to
turn off the front panel FL display.
The
The
DISP
indicator will illuminate
to remind you that the unit is still
turned on.
turned on.
!
OSD (On Screen Display):
Press
the button briefly to display a system
status report on your video screen.
status report on your video screen.
@
Delay:
Press this button to
increase the delay to the rear (sur-
round) channels.
round) channels.
#
Mode:
Press these buttons to
scroll up
⁄
or down
¤
through the
list of available surround modes.
$
P-Set:
Press these buttons to
manually scroll up
⁄
or down
¤
through the FM or AM stations pro-
grammed into the receiver’s preset
memory.
grammed into the receiver’s preset
memory.
%
P-Scan:
Press this button to
automatically scan through the FM
or AM stations preset into the receiv-
er’s memory. Press the button again
to stop the scan when the tuner is at
the desired station.
or AM stations preset into the receiv-
er’s memory. Press the button again
to stop the scan when the tuner is at
the desired station.
^
Tune:
Press these buttons to
manually scan up
⁄
or down
¤
through the FM or AM bands.
&
Mute:
Press this button to cut the
output to the speakers. Press it
again to return to the previous vol-
ume level.
again to return to the previous vol-
ume level.
*
Volume Control:
Turn the knob
clockwise to increase volume, coun-
terclockwise to decrease the vol-
ume. Note that approximately two
revolutions of the knob are required
to go from no output to maximum
volume.
terclockwise to decrease the vol-
ume. Note that approximately two
revolutions of the knob are required
to go from no output to maximum
volume.
(
Power:
Press this button once to
turn the unit on or off. In order to use
the remote control to turn the unit on
the power switch must be pressed
once, and then the unit must be
turned off via the remote.
the remote control to turn the unit on
the power switch must be pressed
once, and then the unit must be
turned off via the remote.
Ó
Headphone Jack:
Plug standard
stereo headphones into this jack for
private listening.
private listening.
NOTE:
When the headphones are in
use the output to the speakers is
muted and the surround mode is
automatically switched to
muted and the surround mode is
automatically switched to
STEREO
.
When the headphones are removed
from the jack, sound to the speakers
is restored and the unit returns to the
previous sound mode.
from the jack, sound to the speakers
is restored and the unit returns to the
previous sound mode.
Ô
6 Channel Direct:
Press this but-
ton to select the output of an exter-
nal multichannel audio adapter.
nal multichannel audio adapter.
Tape 1 Copy:
Press this button to
select the input for the recorder con-
nected to
Tape 1
. The first press will
select the source currently being lis-
tened to. Press again to select the
input in the following order:
Tuner‡CD‡Tape2‡Source.
tened to. Press again to select the
input in the following order:
Tuner‡CD‡Tape2‡Source.
Ò
VCR 1 Copy:
Press this button
to select the input to the recorder
connected to VCR 1. The first
press selects the input currently
being viewed. Press the button
again to select the input in the
following order:
TV‡LD‡VCR2‡AUX‡Source
connected to VCR 1. The first
press selects the input currently
being viewed. Press the button
again to select the input in the
following order:
TV‡LD‡VCR2‡AUX‡Source
Ú
Memo:
The memo button is used
to enter stations to the tuner’s preset
memory in either the manual or auto-
matic modes. It is also used clearing
the memory and when changing the
TV auto on-mode.
memory in either the manual or auto-
matic modes. It is also used clearing
the memory and when changing the
TV auto on-mode.
Û
Clear:
The clear button is used
to cancel tuning, memory input or
when clearing the unit’s memories.
when clearing the unit’s memories.
Ù
FM Mode:
Press this button
to select the tuning mode for FM
stations.
stations.
ı
Bass:
This knob adjusts the tone
of low frequency sounds.
Turn it to the right to boost bass
frequencies or to the left to cut bass
frequencies.
Turn it to the right to boost bass
frequencies or to the left to cut bass
frequencies.
ˆ
Treble:
This knob adjusts
the tone of high frequency sounds.
Turn to it the right to boost high
frequencies or to the left to cut high
frequencies.
Turn to it the right to boost high
frequencies or to the left to cut high
frequencies.
˜
Balance:
This knob adjusts the
balance between the front left and
right speakers.
right speakers.
¯
Front Panel Inputs:
Audio or
Video sources connected to these
jacks may be selected by pressing
the
jacks may be selected by pressing
the
Aux
button
8.
5
•AVR80mkII 120 (f).qx 2/5/99 9:56 AM Page 6
Click on the first or last page to see other AVR 80MK II (serv.man4) service manuals if exist.