Read Harman Kardon AVR 80MK II (serv.man4) User Guide / Operation Manual online
Rear Panel Audio and System Connections
å
FM Antenna:
Connect an indoor
or external FM antenna to these
terminals.
terminals.
∫
AM Antenna:
Connect the AM
loop antenna supplied with the
receiver to these terminals. If an
external AM antenna is used, make
connections to the
receiver to these terminals. If an
external AM antenna is used, make
connections to the
AM
and
GND
terminals in accordance with the
instructions supplied with the
antenna.
instructions supplied with the
antenna.
ç
Tape 1 Out:
Connect these jacks
to the RECORD/INPUT jacks of an
audio recorder.
audio recorder.
∂
Tape 1 In:
Connect these jacks to
the PLAY/OUT jacks of an audio
recorder.
recorder.
é
Tape 2 Out:
Connect these jacks
to the RECORD/INPUT jacks of a
second audio recorder.
second audio recorder.
ƒ
Tape 2 In:
Connect these jacks to
the PLAY/OUT jacks of a second
audio recorder.
audio recorder.
©
CD IN:
Connect these jacks to
the output of a compact disc player
or CD changer.
or CD changer.
˙
Front R:
Connect these terminals
to the front right speaker.
î
Front L:
Connect these terminals
to the front left speaker.
∆
Center:
Connect these terminals
to the center speaker.
˚
Surround R:
Connect these ter-
minals to the right surround speaker.
¬
Surround L:
Connect these ter-
minals to the left surround speaker.
µ
Subwoofer Pre-Out:
Connect
this jack to the line level input of a
powered subwoofer. If an external
subwoofer amplifier is used, connect
this jack to the subwoofer amplifier
input.
powered subwoofer. If an external
subwoofer amplifier is used, connect
this jack to the subwoofer amplifier
input.
ñ
Pre-Outs:
If external power
amplifiers are used for any channels,
remove the jumper pin and connect
the jack to the input of the amplifier.
remove the jumper pin and connect
the jack to the input of the amplifier.
ø
6 Channel Direct Input:
If an
external digital audio decoder is
used for 5.1 (Dolby Digital) audio,
connect the outputs of that decoder
to these terminals.
used for 5.1 (Dolby Digital) audio,
connect the outputs of that decoder
to these terminals.
π
Multi Room Interface:
For multi-
room installations where keypad
remotes are in use, connect the key-
pad interface to this jack.
remotes are in use, connect the key-
pad interface to this jack.
œ
Multi IR:
Connect the output of
an IR sensor in a remote room to this
jack to operate the AVR80
jack to operate the AVR80
II
’s multi-
room control system.
®
Multi-Out:
When using the
AVR80
II
for multi-room audio, con-
nect this jack to the input of the
audio amplifier powering the remote
room speakers.
audio amplifier powering the remote
room speakers.
ß
Power Cable:
Connect the AC
plug to a non-switched AC wall
output.
output.
†
Switched AC Outlet:
This outlet
may be used to power any device
that you wish to have on when the
unit is turned on.
that you wish to have on when the
unit is turned on.
ü
Unswitched AC Outlet:
This out-
let may be used to power any AC
device. The power will remain on at
this outlet regardless of whether the
AVR80
device. The power will remain on at
this outlet regardless of whether the
AVR80
II
is on or off.
NOTE:
The power consumption of
the device plugged into each of
these outlets should not exceed 120
watts.
these outlets should not exceed 120
watts.
√
Remote IR In:
If the AVR80
II
’s
front panel IR sensor is blocked due
to cabinet doors or other obstruc-
tions, an external IR sensor may be
used. Connect the output of the sen-
sor to this jack.
to cabinet doors or other obstruc-
tions, an external IR sensor may be
used. Connect the output of the sen-
sor to this jack.
∑
Remote IR Out:
This connection
permits the IR sensor in the receiver
to serve other remote controlled
devices. Connect this jack to the “IR
IN” jack on Harman Kardon or other
compatible equipment.
to serve other remote controlled
devices. Connect this jack to the “IR
IN” jack on Harman Kardon or other
compatible equipment.
9
•AVR80mkII 120 (f).qx 2/5/99 9:56 AM Page 10
Click on the first or last page to see other AVR 80MK II (serv.man4) service manuals if exist.