Read Harman Kardon AVR 75 (serv.man2) Service Manual online
AVR75 & AVR85 REMOTE CONTROL INFORMATION ...continued
1.
Use/Learn: This switch selects the operation mode of the
remote control. Slide it to the left for normal operation. Slide
it to the right when the remote is being programmed.
2.
Source Power: When power on/off commands have
been programmed into the remote’s memory, press these
buttons to control power for the last source device selected.
3.
Main Power: Press these buttons to turn the unit on or
off (to Standby Mode).
4.
Source Selection: Pressing one of these buttons selects
the input source that will be listened to through the receiver.
When a source is selected the remote’s transport and
numeric number buttons will also transmit the commands
needed to control that machine.
5.
Night Mode: Press this button to activate the “Night”
mode, preventing loud playback when the digital modes are
in use without altering the dynamic range of the output
signal.
6.
Delay: Press this button to change the delay for the
surround channels when the Surround Mode Menu is on the
screen.
7.
Digital Audio Input Selectors: Press one of these
buttons to select a digital input source. The digital audio
source may be the same as, or different analog audio of the
selected video source.
8.
Multiroom Control: Press this button to turn the remote
room feed on or off. The Multi indicator
will light or flash
when the remote feed is on. Note that the remote zone feed
will remain on after the main room power is turned off until it
is switched off by pressing this button again.
9.
Menu Controls: These buttons control the action of the
cursor or the selection of menu items when the receiver is
being configured using the setup menus.
10.
Select: This button enters settings to the receiver’s
memory during system configuration.
11.
OSD: Press this button to activate the on-screen menu
system.
12.
Test Tone: Press this button to begin calibration of the
output level for each channel. A test signal will immediately
be heard from the left front speaker and the Test indicator
will flash.
13.
Channel Select: Press this button to view a status
report of the output level for each channel. When the Test
Tone is audible and the system output levels are being set,
pressing this button will advance the channel being adjusted
in a clockwise direction to the next channel.
14.
Speaker Level Adjust: When setting the system output
levels, press these buttons to increase or decrease the
output level.
15.
Main Volume: These buttons control the unit’s volume.
Note that all channels are controlled simultaneously.
16.
Display: Press this button to turn off all displays and
indicators in the Information Display except for a small Disp
indication in the lower right corner of the display
indication in the lower right corner of the display
. Press
the button again to turn the display back on.
17.
Mute: Press this button to temporarily cut the audio
output of the receiver. Press it again to return to the
previous volume level.
18.
Transport Controls: These buttons may be
programmed to control the tape or disc motion of the last
playback source selected with the Source Selection
buttons
buttons
. Use them as you would the Play, Stop, Pause,
Record, Reverse Play and Forward Play buttons on any
VCR, CD, cassette, DVD or LD remote control. The
Reverse Play button
also operates the FM Mode
function of the AVR75/85’s tuner.
NOTE: The
,
and
buttons are also used
to control the PTY, AF and RDS Display functions of the
tuner.
19.
Tune/Search & Fast Forward: These buttons may be
programmed to have multiple functions, which vary
according to the input device selected.
a. When the TUNER has been selected, these buttons
are used to tune stations.
b. When CD, Tape, DVD, LD or VCR is the input source,
these buttons act as the Fast Scan Forward
or
Fast Scan Reverse
controls.
1 0
Harman Kardon
Dolby Digital Audio/Video Receiver
AVR75/85
D
P
I
4
Click on the first or last page to see other AVR 75 (serv.man2) service manuals if exist.