Read Harman Kardon AVR 35 (serv.man2) Service Manual online
Delay :
Digital Input Selector :
Optical
Coaxial
Digital
Set Button :
Channel Selector :
Speaker Selector Button :
Selector Buttons :
Information Display :
Remote Sensor Window :
Press this button to begin the
sequence of steps required to enter delay time
settings.
When playing a
source that has a digital output, press this button
to select between the
(17) and
(16)
inputs.
When making choices during
the setup and configuration process, press this
button to enter the desired setting, as shown in
the information Display, into the AVR-35's
memory.
Press this button to
begin the process of selecting and configuring
the AVR-35's output channels.
Press this button
to begin the process of selecting the speaker
positions that are used in your listening room.
When you are
establishing the AVR-35's configuration settings,
use these buttons to select between the choices
available. as shown in the information Display
.
This display delivers
messages and status indications to help you
operate the receiver.
The sensor
behind this window receives infrared signals from
the remote control. Aim the remote at this area
and do not block or cover it unless an external
remote sensor is installed.
listening to a program that carries the Dolby
Digital surround mode when listening to a
program that carries the Dolby Digital information.
Press this
button to select the Dolby Pro Logic surround
mode when listening to an analog or
digital(PCM) program that is encoded with
surround-sound information.
Press this button
to select the Dolby 3 Stereo listening mode.
This mode is used primarily when a program
has surround information when a center channel
speaker, but no surround speakers, is installed.
Press one of
these buttons to select the analog surround
modes. These modes may be used with any
analog program source to create a pleasing
surround effect.
press this button to begin to
sequence of steps used to set the AVR-35's
output levels. When this button is pressed, a test
tone will replace the currently selected listening
source.
Press this button to turn off
all surround processing, and to listen to a
program in traditional stereo from the left front
and right front speakers only.
Press this button to momentarily
silence the speaker output of the AVR-35.
Turn the knob clockwise to
increase volume, counter clockwise to decrease
the volume.
Dolby Pro Logic Selector :
Dolby 3 Stereo Selector :
Surround Mode Selectors :
Test Tone :
Surround Off :
Mute :
Volume Control :
Tuning button :
TUNED
Press the left side of the
button to tune lower frequency station and the
right side of the button to tune higher frequency
stations. When a station with a strong signal is
tuned, the
indicator
will illuminate in
the Information Display
. A brief(1/2 second)
press of the button will manually tune to the next
frequency increment, while pressing and holding
the button for a long period will automatically
tune to the next station with a signal strong
enough for acceptable reception.
Press this button to
automatically scan through the station that have
been programmed in the AVR-35's memory.
The tuner will play five seconds of each station
before moving to the next preset station. To stop
the scan when the desired station is heard, press
the button again.
Press this button
to select stations that have been entered into the
preset memory.
Press this button to
select the auto or mono mode for FM tuning.
In the AUTO mode,
indicator will
illuminate in the information display, and when
stations are transmitting stereo signals, the
stereo reception will be provided and
indicator will also be illuminated in the
information display. In the MONO mode the left
and right signals from stereo broadcasts will be
mixed together and reproduced through all
channels. Select MONO for better reception of
weak signals.
Press this button to
select the Dolby Digital surround mode when
Preset Scan :
Preset Stations Selector :
TUN.MODE/RDS :
AUTO
Stereo
Dolby Digital Selector :
information Display
CD :
DVD Input :
Video Input Selectors :
Audio/Video
AM/FM :
Sleep Button :
, and the red LED
above the button will illuminate to remind you
that you are listening to the tape monitor..
Press this button to select the device
connected to the CD Input jacks (5) as the
listening source.
Press this button to select the
device connected to the DVD Input jacks (6) as
the listening and viewing source.
Press one of these
buttons to select a source connected to the rear
panel
inputs (3), (14), or the front
panel
Press this button to select the
tuner as the AVR-35's input source. When it is
first pressed the last station tuned will be heard.
Press it again to change between AM and FM
bands.
Audio/Video input
.
Press this button to place
the unit in the Sleep mode. After the time shown
in the dispaly, the AVR35 will automatically go
into the Standby mode. Each press of the button
changes the time until turn-off in the following
order :
Main Power Switch :
NOTE :
System Power Control :
Power Indicator
Power Indicator :
Head Phone Jack :
Press this button to
apply power to the AVR-35.
When the switch is pressed in the unit is placed
in a Standby mode, as indicated by the amber
LED.
This button MUST be pressed in to operate the
unit. To turn the unit off and prevent the use of
the remote control, this switch should be pressed
until it pops out from the panel so that the word
"OFF" may be read at the top of the switch.
In normal operation this switch is left in
the "ON" position.
When the Main
Power Switch 1 is "ON", press this button to
turn on the AVR-35 ; press it again to turn the
unit off. Note that the
surrounding the switch
will turn green when
the unit is on.
This LED will illuminate in
amber when the unit is in the Standby mode to
signal that the unit is ready to be turned on.
When the unit is in operation, the indicator will
turn green.
This jack may be used
to listen to the AVR-35's output through a pair of
headphones. Be certain that the headphones
have a standard 1/4" stereo phone plug.
Bass Control :
Treble Control :
Balance Control :
NOTE :
Video 3 Inputs :
T-Mon Selector :
Tape Monitor
Turn this control to modify
the lower frequency output of the left / right
channels by as much as +/-10dB. Set this
control to a suitable position for your taste and
room acoustics.
Turn this control to modify
the high frequency output of the left / right
channels by as much as +/-10dB.
Set this control to a suitable position for your
taste and room acoustics.
Turn this control to
change the relative volume for the front left /
right channels.
For proper operation of the surround
modes this control should be at the midpoint, or
"12 o'clock" position.
These audio / video inputs
may be used for temporary connection of video
games, camcorder, digital still cameras or
portable audio products. To select a source
connected to these jacks, press the Video 3
Input Selector
.
Press this button to select
the device connected to the
jacks
(20) as the listening source. The previously
selected source will continue to show in the
CONTROLS AND FUNCTIONS
Front Panel
32
30
20
10
5
1
OFF
90
80
70
60
50
40
min min min min min min
min min min min min
min
Click on the first or last page to see other AVR 35 (serv.man2) service manuals if exist.