Read Harman Kardon AVR 255 (serv.man3) EMC - CB Certificate online
IEC 60065 7ed. (2001)
- Page 3 of 3 -
www.nemko.com
Report No. 98389
14.3.3
Transformer/motor, constructional requirements
P
Transformer
Part No.
Part No.
Insulation
between
between
Insulation Res.
M Ohms
Test Volt
V (60 sec.)
Clearances / Creepage distances
Measured
Required
CLT(
or
KLT)5W032ZE
Pr - sec
> 100
3KV (rms)
10,4 / 10,4 mm
4,0 / 5,6 mm
Pr - ic
> 100
3KV (rms)
10,3 / 10,3 mm
4,0 / 5,0 mm
CLT(
or
KLT)5I009ZE
Pr - Sec
> 100
3 kV (rms)
6,9 / 6,9 mm
4,0 / 5,0 mm
Pr - ic
> 100
3 kV (rms)
5,2 / 5,2 mm
4,0 / 5,0 mm
-
Components / construction
CLT(
or
KLT)5W032ZE
Windings on two separate bobbins. The bobbins are placed
in an insulating housing with two compartments, one above
the other. Bobbin thickness: > 0,4mm.
Max. Working Voltage: 382Vp/270Vrms
in an insulating housing with two compartments, one above
the other. Bobbin thickness: > 0,4mm.
Max. Working Voltage: 382Vp/270Vrms
P
Components / construction
CLT(
or
KLT)5I009ZE
Windings on single bobbin. The center flange provided
between primary and secondary windings.
Satisfactory constructed. Bobbin thickness: > 0,4mm.
Max. Working voltage: 338Vp/239Vrms
between primary and secondary windings.
Satisfactory constructed. Bobbin thickness: > 0,4mm.
Max. Working voltage: 338Vp/239Vrms
P
Transformer
Part No
Part No
Insulation
Between
Between
Thick (mm)
X Number
Material
Dielectric strength test
60 sec.
CLT(
or
KLT)5W032ZE Pr - sec
0,90 mm min. x 1
PET bobbin
Pass *)
Pr - ic
0,90 mm min. x 1
PET bobbin
Pass *)
CLT(
or
KLT)5I009ZE
Pr - sec
0,70 mm min. x 2
0,70 mm min. x 1
0,70 mm min. x 1
PBT bobbin flange
PBT bobbin cap.
PBT bobbin cap.
Pass *)
Pr - ic
0,60 mm min. x 1
PBT bobbin
Pass *)
Pr - ic
0,60 mm min. x 1
PBT bobbin cap.
Pass *)
*) Test voltage: 3000 Vrms.
17.1
Torque test to Table 20:
P
Screw
Diameter
With
Without
Material
Torque test (Nm)
Location / function
(mm)
Head
Head
Screw
Nut
Fulfilled / Remarks
Fixing of top cover
(sides)
(sides)
4,0 x -
Metal
Metal
Tested with 1,2Nm,
5 times / Pass
5 times / Pass
Fixing of top cover
(rear)
(rear)
3,0 x -
Metal
Metal
Tested with 0,5Nm,
5 times / Pass
5 times / Pass
Click on the first or last page to see other AVR 255 (serv.man3) service manuals if exist.