AVR 200 (serv.man7) - Harman Kardon Audio User Guide / Operation Manual. Page 6

FRONT-PANEL CONTROLS 5

1 Main Power Switch: Press this button to
apply power to the AVR 200RDS. When the
switch is pressed in, the unit is placed in a
Standby mode, as indicated by the amber LED
3 surrounding the System Power Control
2. This button MUST be pressed in to operate
the unit. To turn the unit off completely and
prevent the use of the remote control, this
switch should be pressed until it pops out from
the front panel so that the word “OFF” may be
read at the top of the switch.
NOTE: In normal operation this switch is left in
the “ON” position.

2 System Power Control: When the Main
Power Switch 1 is “ON,” press this button
to turn on the AVR 200RDS; press it again to
turn the unit off (Standby). Note that the
Power Indicator surrounding the switch 3
will turn green when the unit is on.

3 Power Indicator: This LED will illuminate
in amber when the unit is in the Standby mode
to signal that the unit is ready to be turned on.
When the unit is in operation, the indicator will
turn green.

4 Headphone Jack: This jack may be used to
listen to the AVR 200RDS’s output through a
pair of headphones. Be certain that the head-
phones have a standard 6.3 mm stereo phone
plug. Note that the speakers and any Surround
mode will automatically be turned off when the
headphone jack is in use.

5 Bass Control: Turn this control to modify
the low-frequency output of the left/right chan-
nels by as much as ±10dB. Set this control to a
suitable position for your taste or room
acoustics.

6 Treble Control: Turn this control to modify
the high-frequency output of the left/right
channels by as much as ±10dB. Set this control
to a suitable position for your taste or room
acoustics.

7 Balance Control: Turn this control to
change the relative volume for the front
left/right channels.

8 Video 3 Inputs: These audio/video inputs
may be used for temporary connection of video
games, camcorders, digital still cameras or
portable audio products. To select a source 
connected to these jacks, press the Vid 3 Input
Selector #.

9 Sleep Button: Press this button to place
the AVR in the Sleep mode. Once the button is
pressed, Information Display 35 will show
the time remaining before the unit will auto-

1 Main Power Switch
2 System Power Control
3 Power Indicator
4 Headphone Jack
5 Bass Control
6 Treble Control
7 Balance Control
8 Video 3 Inputs
9 Sleep Button
) Tape Input Selector
! CD Input Selector
@ DVD Input Selector

# Video Input Selector
$ 6-Channel Selector
% AM/FM Button
^ Tuning Selector
& Preset Scan
* Preset Stations Selector
( Tuner Mode
Ó Dolby Digital Selector
Ô Dolby Pro Logic Selector
 Dolby 3 Stereo Selector
Ò Hall Mode Selector
Ú Theater Mode Selector

Û Test Tone Button
Ù Surround Off
ı Mute
ˆ Volume Control
˜ Delay
¯ Digital Input Selector
˘ Set Button
¸ Channel Trim Button
33 Speaker Select Button
34 Selector Buttons
35 Information Display
36    Remote Sensor 

TAPE

SLEEP

CD

DVD

VID 1

VID 2

VID 3

6 CH.

AM/FM

PRESET SCAN

FM MODE

HALL

THEATER

TEST TONE

SURR. OFF

PRESET

TUNING

DIGITAL

PRO LOGIC

3-STEREO

9 ) ! @

#

$ %

^

&

Ó

3

4

5

6

7

8

1

2

(

*

Ô

Ò

¯

ˆ

˘

˜



ÚÛ

ı

Ù

¸