Read Sony DSX-S300BTX Service Manual online
DSX-S300BTX
3
SECTION 1
SERVICING NOTES
IMPORTANT NOTE OF “INITIALIZING”
The purpose of “Bluetooth Initialize” is to initialize the Bluetooth
connection history (HF/Audio Streaming). (To delete the device
information for the devices that you connected to when searching,
etc.)
When the BT board or MAIN board (including BT board) are re-
placed, it is necessary to initialize this set.
Refer to the following, initialize this set.
The purpose of “Bluetooth Initialize” is to initialize the Bluetooth
connection history (HF/Audio Streaming). (To delete the device
information for the devices that you connected to when searching,
etc.)
When the BT board or MAIN board (including BT board) are re-
placed, it is necessary to initialize this set.
Refer to the following, initialize this set.
Note: Phonebook data and dialed/received call history can be deleted by
executing “Reset.”
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong
viscosity
Unleaded solder is more viscous (sticky, less prone to fl ow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
Replacing the lithium battery of the card remote
commander
commander
Under normal conditions, the battery will last approximately 1 year.
(The service life may be shorter, depending on the conditions of use.)
When the battery becomes weak, the range of the card remote commander
becomes shorter. Replace the battery with a new CR2025 lithium battery.
Use of any other battery may present a risk of fire or explosion.
(The service life may be shorter, depending on the conditions of use.)
When the battery becomes weak, the range of the card remote commander
becomes shorter. Replace the battery with a new CR2025 lithium battery.
Use of any other battery may present a risk of fire or explosion.
+ side up
D
Notes on the lithium battery
• Keep the lithium battery out of the reach of children. Should the battery be
• Keep the lithium battery out of the reach of children. Should the battery be
swallowed, immediately consult a doctor.
• Wipe the battery with a dry cloth to assure a good contact.
• Be sure to observe the correct polarity when installing the battery.
• Do not hold the battery with metallic tweezers, otherwise a short-circuit
• Be sure to observe the correct polarity when installing the battery.
• Do not hold the battery with metallic tweezers, otherwise a short-circuit
may occur.
WARNING
Battery may explode if mistreated.
Do not recharge, disassemble, or dispose of
in fire.
Do not recharge, disassemble, or dispose of
in fire.
Initializing Bluetooth Settings
You can initialize all the Bluetooth-related
settings from this unit.
settings from this unit.
1
Press and hold the multi way encoder.
The menu list appears.
The menu list appears.
2
Rotate the multi way encoder to select
“BT Initialize,” then press it.
The confirmation appears.
“BT Initialize,” then press it.
The confirmation appears.
3
Rotate the multi way encoder to select
“Yes.”
“Initializing...” appears while initializing the
Bluetooth settings.
“Yes.”
“Initializing...” appears while initializing the
Bluetooth settings.
4
Press
(BACK).
The display returns to normal reception/play
mode.
mode.
Note
When disposing of this unit, phonebook data should
be deleted with “BT Initialize.”
When disposing of this unit, phonebook data should
be deleted with “BT Initialize.”
ABOUT THE BT BOARD REPLACEMENT
When repairing, the complete BT board should be replaced since
any parts in the BT board cannot be repaired.
When repairing, the complete BT board should be replaced since
any parts in the BT board cannot be repaired.
NOTE FOR THE 24-PIN CONNECTOR (CN901)
Do not use alcohol to clean the 24-pin connector (CN901) connect-
ing the front panel with the main body.
Do not touch the connector directly with your bare hand. Poor con-
tact may be caused.
Do not use alcohol to clean the 24-pin connector (CN901) connect-
ing the front panel with the main body.
Do not touch the connector directly with your bare hand. Poor con-
tact may be caused.
NOTE FOR CHECKING THE MAIN BOARD
If removing the MAIN board from the chassis to check it sepa-
rately without attaching the front panel, hold the detach detection
switch (S702) ON by using tape or the like, and then start opera-
tions.
If removing the MAIN board from the chassis to check it sepa-
rately without attaching the front panel, hold the detach detection
switch (S702) ON by using tape or the like, and then start opera-
tions.
– MAIN Board (Component Side) –
S702
tape
You can cancel the demonstration display which
appears during turning off.
appears during turning off.
1
Press and hold the multi way encoder.
The setup display appears.
The setup display appears.
2
Rotate the multi way encoder to select
“Demo,” then press it.
“Demo,” then press it.
3
Rotate the multi way encoder to select
“off.”
“off.”
4
Press and hold the multi way encoder.
The setup is complete and the display returns
to normal reception/play mode.
The setup is complete and the display returns
to normal reception/play mode.
CANCELING THE DEMO MODE
Click on the first or last page to see other DSX-S300BTX service manuals if exist.