Read Sony CDX-GT720 / CDX-GT72W / CDX-GT770 Service Manual online
SERVICE MANUAL
Published by Sony Techno Create Corporation
Sony Corporation
Audio Business Group
SPECIFICATIONS
FM/AM COMPACT DISC PLAYER
9-887-940-01
2007L04-1
©
2007.12
US Model
CDX-GT72W/GT720
E Model
CDX-GT770
Ver. 1.0 2007.12
Model Name Using Similar Mechanism
NEW
CD Drive Mechanism Type
MG-101FC-188//Q
Optical Pick-up Name
DAX-25A
• The tuner and CD sections have no adjustments.
(Photo: CDX-GT720)
CD Player section
Signal-to-noise ratio: 120 dB
Frequency response: 10 – 20,000 Hz
Wow and fl utter: Below measurable limit
Frequency response: 10 – 20,000 Hz
Wow and fl utter: Below measurable limit
Tuner section
FM
Tuning range:
CDX-GT72W/GT720:
87.5 – 107.9 MHz
CDX-GT770:
87.5 – 108.0 MHz (at 50 kHz step)
87.5 – 107.9 MHz (at 200 kHz step)
FM tuning interval:
CDX-GT770:
50 kHz/200 kHz switchable
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency: 10.7 MHz/450 kHz
Usable sensitivity: 9 dBf
Selectivity: 75 dB at 400 kHz
Signal-to-noise ratio:
67 dB (stereo), 69 dB (mono)
Harmonic distortion at 1 kHz:
0.5 % (stereo), 0.3 % (mono)
Separation: 35 dB at 1 kHz
Frequency response: 30 – 15,000 Hz
Tuning range:
CDX-GT72W/GT720:
87.5 – 107.9 MHz
CDX-GT770:
87.5 – 108.0 MHz (at 50 kHz step)
87.5 – 107.9 MHz (at 200 kHz step)
FM tuning interval:
CDX-GT770:
50 kHz/200 kHz switchable
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency: 10.7 MHz/450 kHz
Usable sensitivity: 9 dBf
Selectivity: 75 dB at 400 kHz
Signal-to-noise ratio:
67 dB (stereo), 69 dB (mono)
Harmonic distortion at 1 kHz:
0.5 % (stereo), 0.3 % (mono)
Separation: 35 dB at 1 kHz
Frequency response: 30 – 15,000 Hz
AM
Tuning range:
CDX-GT72W/GT720:
530 – 1,710 kHz
CDX-GT770:
531 – 1,602 kHz (at 9 kHz step)
530 – 1,710 kHz (at 10 kHz step)
AM tuning interval:
CDX-GT770:
9 kHz/10 kHz switchable
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency: 10.7 MHz/450 kHz
Sensitivity: 30
Tuning range:
CDX-GT72W/GT720:
530 – 1,710 kHz
CDX-GT770:
531 – 1,602 kHz (at 9 kHz step)
530 – 1,710 kHz (at 10 kHz step)
AM tuning interval:
CDX-GT770:
9 kHz/10 kHz switchable
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency: 10.7 MHz/450 kHz
Sensitivity: 30
μV
Power amplifi er section
Outputs: Speaker outputs (sure seal connectors)
Speaker impedance: 4 – 8 ohms
Maximum power output: 52 W × 4 (at 4 ohms)
Speaker impedance: 4 – 8 ohms
Maximum power output: 52 W × 4 (at 4 ohms)
General
Outputs:
Audio outputs terminal (front/rear)
Subwoofer output terminal (mono)
Power antenna (aerial) relay control terminal
Power
Audio outputs terminal (front/rear)
Subwoofer output terminal (mono)
Power antenna (aerial) relay control terminal
Power
amplifi er control terminal
Inputs:
Telephone ATT control terminal
Illumination control terminal
BUS control input terminal
BUS audio input terminal
Remote controller input terminal
Antenna (aerial) input terminal
AUX input jack (stereo mini jack)
Tone controls:
Low: ±10 dB at 60 Hz (XPLOD)
Mid: ±10 dB at 1 kHz (XPLOD)
High: ±10 dB at 10 kHz (XPLOD)
Power requirements: 12 V DC car battery
(negative ground (earth))
Dimensions: Approx. 178 × 50 × 190 mm
(7
Telephone ATT control terminal
Illumination control terminal
BUS control input terminal
BUS audio input terminal
Remote controller input terminal
Antenna (aerial) input terminal
AUX input jack (stereo mini jack)
Tone controls:
Low: ±10 dB at 60 Hz (XPLOD)
Mid: ±10 dB at 1 kHz (XPLOD)
High: ±10 dB at 10 kHz (XPLOD)
Power requirements: 12 V DC car battery
(negative ground (earth))
Dimensions: Approx. 178 × 50 × 190 mm
(7
1/8
× 2 × 7
1/2
in.) (w/h/d)
Mounting dimensions:
Approx. 182 × 53 × 163 mm
(7
Approx. 182 × 53 × 163 mm
(7
1/4
× 2
1/8
× 6
1/2
in.) (w/h/d)
Mass: Approx. 1.6 kg (3 lb 9 oz)
Supplied accessories:
Card remote commander:
RM-X152
Supplied accessories:
Card remote commander:
RM-X152
(CDX-GT72W/GT720)
RM-X156
(CDX-GT770)
Parts for installation and connections (1 set)
Design and specifi cations are subject to change
without notice.
without notice.
AUDIO POWER SPECIFICATIONS
(CDX-GT72W/GT720)
POWER OUTPUT AND TOTAL HARMONIC DISTORTION
23.2 watts per channel minimum continuous average power into
4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more
than 5% total harmonic distortion.
(CDX-GT72W/GT720)
POWER OUTPUT AND TOTAL HARMONIC DISTORTION
23.2 watts per channel minimum continuous average power into
4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more
than 5% total harmonic distortion.
CDX-GT72W/GT720/GT770
CDX-GT72W/GT720/GT770
2
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostat-
ic break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The fl exible board is easily damaged and should be handled with
care.
ic break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The fl exible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused
on the disc refl ective surface by the objective lens in the optical
pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
The laser beam on this model is concentrated so as to be focused
on the disc refl ective surface by the objective lens in the optical
pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
SERVICE NOTES
CAUTION
Use of controls or adjustments or performance of procedures other than
those specifi ed herein may result in hazardous radiation exposure.
Use of controls or adjustments or performance of procedures other than
those specifi ed herein may result in hazardous radiation exposure.
If the optical pick-up block is defective, please replace the whole
optical pick-up block.
Never turn the semi-fi xed resistor located at the side of optical
pick-up block.
optical pick-up block.
Never turn the semi-fi xed resistor located at the side of optical
pick-up block.
TEST DISCS
Please use the following test discs for the check on the CD section.
Please use the following test discs for the check on the CD section.
YDES-18 (Part No. 3-702-101-01)
PATD-012 (Part No. 4-225-203-01)
SAFETY-RELATED COMPONET WARNING!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR
LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES
PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONC-
TIONNEMENT. NE REMPLACER CES COM- POSANTS QUE
PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DON-
NÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS
PUBLIÉS PAR SONY.
LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES
PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONC-
TIONNEMENT. NE REMPLACER CES COM- POSANTS QUE
PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DON-
NÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS
PUBLIÉS PAR SONY.
optical pick-up
semi-fixed resistor
CDX-GT72W/GT720/GT770
3
1.
SERVICE NOTE
..................................................... 4
2. GENERAL
Location of Controls ....................................................... 5
Connections
....................................................................
6
3. DISASSEMBLY
3-1. Base
Panel
Assy
.............................................................. 13
3-2. Sub Panel Assy ............................................................... 13
3-3. CD Mechanism Block ..................................................... 14
3-4. Driving Section (DB-F07) .............................................. 14
3-5. Main Board ..................................................................... 15
3-6. Servo
3-3. CD Mechanism Block ..................................................... 14
3-4. Driving Section (DB-F07) .............................................. 14
3-5. Main Board ..................................................................... 15
3-6. Servo
Board
.................................................................... 15
3-7. Chassis
(T)
Sub
Assy
...................................................... 16
3-8. Roller Arm Assy .............................................................. 16
3-9. Chassis
3-9. Chassis
(OP)
Assy
........................................................... 17
3-10. Chucking Arm Sub Assy ................................................. 17
3-11. Sled Motor Assy .............................................................. 18
3-12. Optical Pick-up Section .................................................. 19
3-13. Optical Pick-up ............................................................... 19
3-11. Sled Motor Assy .............................................................. 18
3-12. Optical Pick-up Section .................................................. 19
3-13. Optical Pick-up ............................................................... 19
4.
DIAGNOSIS FUNCTION
..................................... 20
5. DIAGRAMS
5-1. Block Diagram –Main Section– ..................................... 23
5-2. Block Diagram –Display Section– ................................. 24
5-3. Printed Wiring Boards –Main Section (1/2)– ................. 26
5-4. Printed Wiring Board –Main Section (2/2)– ................... 27
5-5. Schematic Diagram –Main Section (1/4)– ...................... 28
5-6. Schematic Diagram –Main Section (2/4)– ...................... 29
5-7. Schematic Diagram –Main Section (3/4)– ...................... 30
5-8. Schematic Diagram –Main Section (4/4)– ...................... 31
5-9. Printed Wiring Board –Base Panel Section- ................... 32
5-10. Schematic Diagram –Base Panel Section- ...................... 33
5-11. Printed Wiring Boards –Display Section– ...................... 34
5-12. Schematic Diagram –Display Section– .......................... 35
5-2. Block Diagram –Display Section– ................................. 24
5-3. Printed Wiring Boards –Main Section (1/2)– ................. 26
5-4. Printed Wiring Board –Main Section (2/2)– ................... 27
5-5. Schematic Diagram –Main Section (1/4)– ...................... 28
5-6. Schematic Diagram –Main Section (2/4)– ...................... 29
5-7. Schematic Diagram –Main Section (3/4)– ...................... 30
5-8. Schematic Diagram –Main Section (4/4)– ...................... 31
5-9. Printed Wiring Board –Base Panel Section- ................... 32
5-10. Schematic Diagram –Base Panel Section- ...................... 33
5-11. Printed Wiring Boards –Display Section– ...................... 34
5-12. Schematic Diagram –Display Section– .......................... 35
6.
EXPLODED VIEWS
6-1. Main
Section
................................................................... 43
6-2. Main Board Section ....................................................... 44
6-3. Front
6-3. Front
Section
................................................................... 45
6-4. CD Mechanism Section (MG-101FC-188//Q) ............... 46
7.
ELECTRICAL PARTS LIST
.............................. 47
TABLE OF CONTENTS
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if the
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong
viscosity
Unleaded solder is more viscous (sticky, less prone to fl ow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
This compact disc player is classifi ed as a CLASS 1 LASER
product. The CLASS 1 LASER PRODUCT label is located on the
exterior.
product. The CLASS 1 LASER PRODUCT label is located on the
exterior.
CDX-GT770:
This label is located on the bottom of the chassis.
• CD playback
You can play CD-DA (also containing CD TEXT), CD-R/CD-
RW (MP3/WMA/AAC fi les).
RW (MP3/WMA/AAC fi les).
Type of discs
Label on the disc
CD-DA
MP3
WMA
AAC
CDX-GT72W/GT720/GT770
4
SECTION 1
SERVICE NOTE
EXTENSION CABLE AND SERVICE POSITION
When repairing or servicing this set, connect the jig (extension
cable) as shown below.
When repairing or servicing this set, connect the jig (extension
cable) as shown below.
• Connect the MAIN board (CNP301) and the SERVO board
(CN2) with the extension cable (Part No. J-2502-076-1).
NOTE FOR REPLACEMENT OF THE SERVO BOARD
When repairing, the complete SERVO board (A-1177-362-A)
should be replaced since any parts in the SERVO board cannot be
repaired.
When repairing, the complete SERVO board (A-1177-362-A)
should be replaced since any parts in the SERVO board cannot be
repaired.
NOTE FOR THE OPENING OF THE FRONT PANEL
In this set, the front panel is lowered to below the bottom face
when it is opened.
When servicing the set, place it on a stand having a height of about
2 cm.
In this set, the front panel is lowered to below the bottom face
when it is opened.
When servicing the set, place it on a stand having a height of about
2 cm.
SERVO BOARD
CN2
CN2
MAIN BOARD
CNP301
CNP301
J-2502-076-1
stand