Read Sony HCD-V909AV / MHC-V909AV Service Manual online
— 1 —
SERVICE MANUAL
MICROFILM
HCD-V909AV is the tuner, deck, Video CD and
amplifier section in MHC-V909AV.
amplifier section in MHC-V909AV.
Model Name Using Similar Mechanism
HCD-V800
CD Mechanism Type
CDM38L-5BD21AL
Base Unit Type
BU-5BD21AL
Optical Pick-up Type
KSS-213D/Q-NP
Model Name Using Similar Mechanism
HCD-V800
Tape Transport Mechanism Type
TCM-220WR2
CD
SECTION
SPECIFICATIONS
E Model
Chinese Model
TAPE
DECK
SECTION
HCD-V909AV
COMPACT DISC DECK RECEIVER
— Continued on next page —
— 2 —
MODEL IDENTIFICATION
— BACK PANEL —
— BACK PANEL —
MODEL
PARTS No.
4-991-746-4
4-991-746-9
4-991-753-0
4-991-753-1
4-991-753-2
• Abbreviation
SP : Singapore model
MY : Malaysia model
IA : Indonesian model
CH : Chinese model
TH : Thai model
MY : Malaysia model
IA : Indonesian model
CH : Chinese model
TH : Thai model
MY model
TH model
E, SP model
CH model
IA model
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous ra-
diation exposure.
other than those specified herein may result in hazardous ra-
diation exposure.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
Laser component in this product is capable of emitting radiation
exceeding the limit for Class 1.
exceeding the limit for Class 1.
This appliance is classified as
a CLASS 1 LASER product.
The CLASS 1 LASER PROD-
UCT MARKING is located on
the rear exterior.
a CLASS 1 LASER product.
The CLASS 1 LASER PROD-
UCT MARKING is located on
the rear exterior.
This caution
label is located
inside the unit.
label is located
inside the unit.
SAFETY-RELATED COMPONENT WARNING !!
COMPONENTS IDENTIFIED BY MARK
!
OR DOTTED LINE
WITH MARK
!
ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repain parts.
The flexible board is easily damaged and should be handled with
care.
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repain parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission, ob-
serve from more than 30 cm away from the objective lens.
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission, ob-
serve from more than 30 cm away from the objective lens.
LASER DIODE AND FOCUS SEARCH OPERATION
CHECK
CHECK
Carry out the “S curve check” in “CD section adjustment” and check
that the S curve waveform is output three times.
that the S curve waveform is output three times.
— 3 —
TABLE OF CONTENTS
1. SERVICING NOTE
.......................................................... 3
2. GENERAL
.......................................................................... 6
3. DISASSEMBLY
3-1. Back Panel ........................................................................... 7
3-2. Loading Panel ....................................................................... 8
3-3. CD Mechanism Deck ............................................................ 8
3-4. Front Panel ........................................................................... 9
3-5. TC Mechanism Deck and DECO Board ............................... 9
3-6. HP/MIC Board, Display Board and TC SW Board ............ 10
3-7. Disc Tray ........................................................................... 10
3-2. Loading Panel ....................................................................... 8
3-3. CD Mechanism Deck ............................................................ 8
3-4. Front Panel ........................................................................... 9
3-5. TC Mechanism Deck and DECO Board ............................... 9
3-6. HP/MIC Board, Display Board and TC SW Board ............ 10
3-7. Disc Tray ........................................................................... 10
4. TEST MODE
..............................................................
11
5. MECHANICAL ADJUSTMENTS
...........................
12
6. ELECTRICAL ADJUSTMENTS
............................... 12
7. DIAGRAMS
7-1. Circuit Boards Location ...................................................... 17
7-2. Block Diagrams
7-2. Block Diagrams
• KEY CON Section ........................................................... 18
• CD Section ....................................................................... 19
• Video Section ................................................................... 21
• Deck Section .................................................................... 23
• Main Section .................................................................... 25
• Power Section .................................................................. 27
• CD Section ....................................................................... 19
• Video Section ................................................................... 21
• Deck Section .................................................................... 23
• Main Section .................................................................... 25
• Power Section .................................................................. 27
7-3. Printed Wiring Board — CD Section — ............................. 29
7-4. Schematic Diagram — CD Section — ............................... 31
7-5. Schematic Diagram — Video Section — ........................... 33
7-6. Printed Wiring Board — Video Section — ......................... 37
7-7. Printed Wiring Board — Main Section — .......................... 40
7-8. Schematic Diagram — Main Section — ............................ 43
7-9. Schematic Diagram — Deck Section — ............................ 47
7-10. Printed Wiring Board — Deck Section — ....................... 51
7-11. Schematic Diagram — Panel Section — ......................... 54
7-12. Printed Wiring Board — Panel Section — ....................... 57
7-13. Schematic Diagram — Power Section — ........................ 61
7-14. Printed Wiring Board — Power Section — ..................... 65
7-15. Schematic Diagram — CD Motor Section — .................. 68
7-16. Printed Wiring Board — CD Motor Section — ............... 69
7-17. Schematic Diagram — KEY CON Section — ................. 71
7-18. Printed Wiring Board — KEY CON Section — .............. 72
7-19. IC Block Diagrams ........................................................... 73
7-20. IC Pin Functions ............................................................... 80
7-4. Schematic Diagram — CD Section — ............................... 31
7-5. Schematic Diagram — Video Section — ........................... 33
7-6. Printed Wiring Board — Video Section — ......................... 37
7-7. Printed Wiring Board — Main Section — .......................... 40
7-8. Schematic Diagram — Main Section — ............................ 43
7-9. Schematic Diagram — Deck Section — ............................ 47
7-10. Printed Wiring Board — Deck Section — ....................... 51
7-11. Schematic Diagram — Panel Section — ......................... 54
7-12. Printed Wiring Board — Panel Section — ....................... 57
7-13. Schematic Diagram — Power Section — ........................ 61
7-14. Printed Wiring Board — Power Section — ..................... 65
7-15. Schematic Diagram — CD Motor Section — .................. 68
7-16. Printed Wiring Board — CD Motor Section — ............... 69
7-17. Schematic Diagram — KEY CON Section — ................. 71
7-18. Printed Wiring Board — KEY CON Section — .............. 72
7-19. IC Block Diagrams ........................................................... 73
7-20. IC Pin Functions ............................................................... 80
8. EXPLODED VIEWS
8-1. Case Section ........................................................................ 97
8-2. Main Board Section ............................................................ 98
8-3. Panel Board Section ............................................................ 99
8-4. Front Panel Section ........................................................... 100
8-5. TC Mechanism Section 1 (TCM-220WR2) ...................... 101
8-6. TC Mechanism Section 2 (TCM-220WR2) ...................... 102
8-7. CD Mechanism Section 1 (CDM38L-5BD29AL) ............ 103
8-8. CD Mechanism Section 2 (CDM38L-5BD29AL) ............ 104
8-9. Base Unit Section (BU-5BD29AL) .................................. 105
8-2. Main Board Section ............................................................ 98
8-3. Panel Board Section ............................................................ 99
8-4. Front Panel Section ........................................................... 100
8-5. TC Mechanism Section 1 (TCM-220WR2) ...................... 101
8-6. TC Mechanism Section 2 (TCM-220WR2) ...................... 102
8-7. CD Mechanism Section 1 (CDM38L-5BD29AL) ............ 103
8-8. CD Mechanism Section 2 (CDM38L-5BD29AL) ............ 104
8-9. Base Unit Section (BU-5BD29AL) .................................. 105
9. ELECTRICAL PARTS LIST
...................................... 106
SECTION 1
SERVICING NOTE
HOW TO OPEN THE DISC TRAY WHEN POWER SWITCH
TURNS OFF
TURNS OFF
1
Remove the Case.
2
Remove the Back panel.
4
Pull-out the disc tray.
3
Turn the cam to the
direction of arrow.
Note for Installation (ROTARY ENCODER)
BU cam
groove
Section A
Note : When attaching the Base unit. insert the
section A into the groove of BU cam.
Note : When attaching the
BU cam, engage the
Rotary encoder switch
as shown in the figure.
Rotary encoder switch
as shown in the figure.
— 4 —
MC Cold Reset
• The cold reset clears all data including preset data stored in the
RAM to initial conditions. Execute this mode when returning the
set to the customer.
set to the customer.
Procedure:
1. Press three buttons NEXT , ENTER/NEXT , and DISC 1
1. Press three buttons NEXT , ENTER/NEXT , and DISC 1
simultaneously.
2. The fluorescent indicator tube becomes blank instantaneously,
and the set is reset.
CD Delivery Mode
• This mode moves the pick-up to the position durable to vibration.
Use this mode when returning the set to the customer after repair.
Procedure:
1. Press POWER button to turn the set ON.
2. Press PLAY MODE button and POWER button simultaneously.
3. A message “LOCK” is displayed on the fluorescent indicator
1. Press POWER button to turn the set ON.
2. Press PLAY MODE button and POWER button simultaneously.
3. A message “LOCK” is displayed on the fluorescent indicator
tube, and the CD delivery mode is set.
MC Hot Reset
• This mode resets the set with the preset data kept stored in the
memory. The hot reset mode functions same as if the power cord
is plugged in and out.
is plugged in and out.
Procedure:
1. Press three buttons NEXT , ENTER/NEXT , and DISC 2
1. Press three buttons NEXT , ENTER/NEXT , and DISC 2
simultaneously.
2. The fluorescent indicator tube becomes blank instantaneously,
and the set is reset.
Sled Servo Mode
• This mode can run the CD sled motor freely. Use this mode, for
instance, when cleaning the pick-up.
Procedure:
1. Select the function “CD”.
2. Press three buttons NEXT , ENTER/NEXT , and FUNC-
1. Select the function “CD”.
2. Press three buttons NEXT , ENTER/NEXT , and FUNC-
TION simultaneously.
3. The Sled Servo mode is selected, if “CD” is blanking on the
fluorescent indicator tube.
4. With the CD in stop status, press
) button in CD section to
move the pick-up to outside track, or
0 button to inside track.
5. To exit from this mode, perform as follows:
1) Move the pick-up to the most inside track.
2) Press three buttons in the same manner as step 2.
2) Press three buttons in the same manner as step 2.
Note:
• Always move the pick-up to most inside track when exiting from
• Always move the pick-up to most inside track when exiting from
this mode. Otherwise, a disc will not be unloaded.
• Do not run the sled motor excessively, otherwise the gear can be
chipped.
Change-over of FUNCTION Name
• The FUNCTION name of external input terminal can be changed
over to VIDEO or MD. With the FUNCTION selected to “MD”,
about 5dB mute is applied to the input gain.
about 5dB mute is applied to the input gain.
Procedure:
1. Press POWER button to turn the set OFF.
2. Press POWER button together with FUNCTION button, and
1. Press POWER button to turn the set OFF.
2. Press POWER button together with FUNCTION button, and
the power is turned on, the display of fluorescent indicator tube
changes to “MD” or “VIDEO” instantaneously, and thus the
FUNCTION is changed over.
changes to “MD” or “VIDEO” instantaneously, and thus the
FUNCTION is changed over.
Change-over of AM Tuner Step between 9kHz and 10kHz
• A step of AM channels can be changed over between 9kHz and
10kHz.
Procedure:
1. Press POWER button to turn the set ON.
2. Select the function “TUNER”, and press TUNER/BAND but-
1. Press POWER button to turn the set ON.
2. Select the function “TUNER”, and press TUNER/BAND but-
ton to select the BAND “AM” or “MW”.
3. Press POWER button to turn the set OFF.
4. Press ENTER/NEXT and POWER buttons simultaneously,
4. Press ENTER/NEXT and POWER buttons simultaneously,
and the display of fluorescent indicator tube changes to “9k
STEP” or “10k STEP”, and thus the channel step is changed
over.
STEP” or “10k STEP”, and thus the channel step is changed
over.
LED and Fluorescent Indicator Tube All Lit, Key Check
Mode
Mode
Procedure:
1. Press three buttons NEXT , ENTER/NEXT , and DISC 3
1. Press three buttons NEXT , ENTER/NEXT , and DISC 3
simultaneously.
2. LEDs and fluorescent indicator tube are all turned on.
Press DISC 2 button, and the key check mode is activated.
3. In the key check mode, the fluorescent indicator tube displays
“K 1 V0 J0”. Each time a button is pressed, “K”value increases.
However, once a button is pressed, it is no longer taken into
account.
“J” Value increases like 1, 2, 3 ... if rotating JOG knob in “+”
direction, or it decreases like 0, 9, 8 ... if rotating in “–” direc-
tion.
“V” Value increases like 1, 2, 3 ... if rotating VOLUME knob in
“+” direction, or it decreases like 0, 9, 8 ... if rotating in “–”
direction.
However, once a button is pressed, it is no longer taken into
account.
“J” Value increases like 1, 2, 3 ... if rotating JOG knob in “+”
direction, or it decreases like 0, 9, 8 ... if rotating in “–” direc-
tion.
“V” Value increases like 1, 2, 3 ... if rotating VOLUME knob in
“+” direction, or it decreases like 0, 9, 8 ... if rotating in “–”
direction.
4. To exit from this mode, press three buttons in the same manner
as step 1, or disconnect the power cord.
Aging Mode
This mode can be used for operation check of CD section and tape
deck section.
• If an error occurred:
deck section.
• If an error occurred:
The aging operation stops.
• If no error occurs:
The aging operation continues repeatedly.
1.
Aging Mode in CD Section
1-1. Operating procedure of Aging Mode
1. Set discs in DISC 1 and DISC 2 trays.
2. Select the function “CD”.
3. Press three buttons NEXT , ENTER/NEXT , and
2. Select the function “CD”.
3. Press three buttons NEXT , ENTER/NEXT , and
KARAOKE PON/MPX simultaneously.
4. The aging mode is activated, if a roulette mark on the fluo-
rescent indicator tube is blinking.
5. In the aging mode, the aging is executed in a sequence given
in “1-2. Operation during Aging Mode”.
The aging continues unless an alarm occurred.
The aging continues unless an alarm occurred.
6. To exit from the aging mode, press POWER button to turn
the set OFF.
•
If a button other than buttons In CD section is pressed during
aging, the aging in the CD section is finished.
aging, the aging in the CD section is finished.
•
To execute aging to the tape deck section successively, press
·
button in the deck A.
“AGING” is displayed on the fluorescent indicator tube. (For
the aging in tape deck, see “2. Aging Mode in Tape Deck Sec-
tion”.
“AGING” is displayed on the fluorescent indicator tube. (For
the aging in tape deck, see “2. Aging Mode in Tape Deck Sec-
tion”.
1-2. Operation during aging Mode
In the aging mode, the program is executed in the following se-
quence.
In the aging mode, the program is executed in the following se-
quence.
1. The disc table is ejected.
2. The disc tray turns to select a disc. (For a disc selection se-
2. The disc tray turns to select a disc. (For a disc selection se-
quence, see Section 1-3.)
3. TOC of disc is read.
4. The pick-up accesses to the last track.
5. Disc table is ejected.
6. Steps 2 through 5 are repeated.
4. The pick-up accesses to the last track.
5. Disc table is ejected.
6. Steps 2 through 5 are repeated.