Read Sharp AR-FN2 (serv.man2) Service Manual online
SERVICE MANUAL
DIGITAL COPIER OPTION
FINISHER
FINISHER
MODEL
AR-FN2
SHARP CORPORATION
Parts marked with "
!
" is important for maintaining the safety of the set. Be sure to replace these parts with specified ones
for maintaining the safety and performance of the set.
[ 1 ] PRODUCT OUTLINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
[ 2 ] SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
[ 3 ] UNPACKING AND INSTALLATION . . . . . . . . . . . . . . . . . . . . . . 1-1
[ 4 ] EXTERNAL VIEW AND INTERNAL STRUCTURE . . . . . . . . . . 4-1
[ 5 ] OPERATIONAL DESCRIPTIONS . . . . . . . . . . . . . . . . . . . . . . . 5-1
[ 6 ] TEST MODE AND SETTING DIP SWITCHES . . . . . . . . . . . . . 6-1
[ 7 ] DISASSEMBLY AND ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . 7-1
[ 8 ] ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
[ 9 ] MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1
[10] TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1
[11] CIRCUIT DESCRIPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1
[12] ELECTRICAL SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1
PARTS GUIDE
CONTENTS
(Danish)
ADVARSEL !
Lithiumbatteri – Eksplosionsfare ved fejlagtig håndtering.
Udskiftning må kun ske med batteri
af samme fabrikat og type.
Levér det brugte batteri tilbage til leverandoren.
(English)
Caution !
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type
recommended by the manufacturer.
Dispose of used batteries according to manufacturer’s instructions.
(Finnish)
VAROITUS
Paristo voi räjähtää, jos se on virheellisesti asennettu.
Vaihda paristo ainoastaan laitevalmistajan suosittelemaan
tyyppiin. Hävitä käytetty paristo valmistajan ohjeiden
mukaisesti.
(French)
ATTENTION
Il y a danger d’explosion s’ il y a remplacement incorrect
de la batterie. Remplacer uniquement avec une batterie du
même type ou d’un type équivalent recommandé par
le constructeur.
Mettre au rebut les batteries usagées conformément aux
instructions du fabricant.
(Swedish)
VARNING
Explosionsfara vid felaktigt batteribyte.
Använd samma batterityp eller en ekvivalent
typ som rekommenderas av apparattillverkaren.
Kassera använt batteri enligt fabrikantens
instruktion.
CAUTION FOR BATTERY REPLACEMENT
[1] PRODUCT OUTLINE
This machine allows separate paper exit to different trays, and sta-
pling of sorted copied sheets. The first-step tray holds 250 sheets,
and the second-step tray holds 750 sheets.
pling of sorted copied sheets. The first-step tray holds 250 sheets,
and the second-step tray holds 750 sheets.
[2] SPECIFICATIONS
1. Type
Installation to copier body (Separate installation allowed)
2. Tray section specifications
Upper tray
Lower tray
Tray type
Normal tray
Lift tray
Capacity
250 sheets (A4/Letter,
80g/m
80g/m
2
)
750 sheets
(A4/Letter, 80g/m
(A4/Letter, 80g/m
2
)
Storing system
Face up
Face up/Face
down
down
Paper exit size
A3
~
A6R
11"
´
17"
~
5 1/2"
´
8 1/2", 12"
´
18"
A4, B5
8 1/2"
8 1/2"
´
11"
Paper weight
52
~
128g/m
2
, 176g/m
2
,
200g/m
2
(For 105g/m
2
or
above, A4/Letter size or
smaller)
smaller)
56
~
128g/m
2
Paper full detection None
Yes
3. Lift tray section
Offset amount
15mm, A4 35mm: B5 24mm: 8.5
´
11
4. Staple section
Storing system
Face up
Stapling system
Flat clinch
Stapling capacity
30 sheets (80g/m
2
)
Applicable size
AB series: A4, B5
Inch series: 8 1/2
Inch series: 8 1/2
´
11
Alignment
Max. shift width: 1mm
Stapling reference
One position (front)
Staple supply system
Cartridge system (5000 pcs.)
Staple
Common with AR-SS1, SF-S54
Detection
Detection of no staple/no cartridge/no
stapler
stapler
5. External dimensions
457mm (W)
´
518mm (D)
´
820mm (H)
552mm (W)
´
518mm (D)
´
866mm (H)(with the upper tray
extended)
6. Weight
22Kg
7. Power
Supplied from the copier body.
[3] UNPACKING AND
INSTALLATION
1. Unpacking
For unpacking, refer to the figure below.
1 – 1
2. Installation
Before installation, check that the following parts are included in the
package.
package.
Unplug the copier’s power cord before carrying out
the following procedure.
the following procedure.
Carry out the following steps before installing the
AR-FN2.
AR-FN2.
1. Pull out the exit unit of the copier until it stops.
2. Remove the two exit area cover fixing screws and remove the exit
area cover.
3. Remove the two transport springs that are attached to the exit
paper guide.
4. Store the two removed transport springs by hanging on the exit
unit front frame (position in Fig. 1).
5. Reattach the exit area cover to its original position and secure it
using two fixing screws.
6. Insert the exit unit into the copier.
1. Attach the connecting plate to the finisher.
Insert the connecting plate into the lower part of the finisher and
secure it using two screws A.
secure it using two screws A.
2. Attach the paper holder lever.
Attach the paper holder lever by inserting it into the mounting location
of the finisher as shown in the figure.
of the finisher as shown in the figure.
3. Attach the exit tray and tray 2.
Insert tray 2 securely into the tray mounting stand and secure it using
one screw A. Then attach the exit tray to the finisher by inserting boss
at (1) first.
one screw A. Then attach the exit tray to the finisher by inserting boss
at (1) first.
Parts included
Tray 2: 1
Connecting plate: 1
Positioning screws: 2
Exit tray: 1
Paper holder lever: 1
Screws A: 3
Screws B: 2
Lock plates: 2
Stapling position label A: 1
Stapling position label B: 1
Screws C: 2
[Fig. 1]
Exit unit
Fixing screw
Exit area cover
Fixing screw
Transport spring
Screws A
Connecting plate
Paper holder lever
Tray 2
Exit tray
Screw A
(2)
(1)
1 – 2