Read Sony SLV-SE610A / SLV-SE610B / SLV-SE610E / SLV-SE610G / SLV-SE610K / SLV-SE610N / SLV-SE710B / SLV-SE710D / SLV-SE710E / SLV-SE710G / SLV-SE710I / SLV-SE710K / SLV-SE710N / SLV-SE810B / SLV-SE810D / SLV-SE810E / SLV-SE810G / SLV-SE810K / SLV-SE810N / SLV-SX71 Service Manual online
1-3
12
Setting up the remote commander
TV control buttons
To
Press
Set the TV to standby mode
?/1
Select an input source: aerial in or line in
t TV/VIDEO
Select the TV’s programme position
Programme number buttons,
-, PROG +/–
PROG +/–/
c/C
2
c/C
2
2
2
2 +/–
1
2
3
4
5
6
7
8
9
0
Programme
number
buttons
number
buttons
WIDE
DISPLAY
????/1
1
1
1
t
t
t
t TV/VIDEO
-
AUDIO MONITOR
FASTEXT buttons
/
a
a
Getti
ng Sta
rted
13
Setting up the remote commander
Notes
• With normal use, the batteries should last about three to six months.
• If you do not use the remote commander for an extended period of time, remove
• With normal use, the batteries should last about three to six months.
• If you do not use the remote commander for an extended period of time, remove
the batteries to avoid possible damage from battery leakage.
• Do not use a new battery together with an old one.
• Do not use different types of batteries together.
• Some buttons may not work with certain Sony TVs.
• Do not use different types of batteries together.
• Some buttons may not work with certain Sony TVs.
* SLV-SE810N/K only
Controlling other TVs with the remote commander
(SLV-SE810N/K only)
(SLV-SE810N/K only)
The remote commander is preprogrammed to control non-Sony TVs. If your
TV is listed in the following table, set the appropriate manufacturer’s code
number.
TV is listed in the following table, set the appropriate manufacturer’s code
number.
* These buttons may not work with all TVs.
Adjust the volume of the TV
2 +/–
Switch to TV (Teletext off)*
a (TV)
Switch to Teletext*
/ (Teletext)
Select the sound
AUDIO MONITOR
Use FASTEXT*
FASTEXT buttons
Call up the on-screen display
DISPLAY
Change the Teletext page*
c/C
Switch to/from wide mode of a Sony wide TV (For
other manufactures’ wide TVs, see “Controlling
other TVs with the remote commander (SLV-
SE810N/K only)” below.)
other manufactures’ wide TVs, see “Controlling
other TVs with the remote commander (SLV-
SE810N/K only)” below.)
WIDE
1
Set
[TV] / [VIDEO] at the top of the remote commander to [TV].
2
Hold down
?/1, and enter your TV’s code number using the programme
number buttons. Then release
?/1.
Now you can use the following TV control buttons to control your TV:
?/1, t TV/VIDEO, programme number buttons, - (ten’s digit),
PROG +/–,
?/1, t TV/VIDEO, programme number buttons, - (ten’s digit),
PROG +/–,
2 +/–, a (TV), / (Teletext), FASTEXT buttons, WIDE*,
MENU*,
M
/
m
/
<
/
,
*, and OK*.
To
Press
continued
14
Setting up the remote commander
Code numbers of controllable TVs
If more than one code number is listed, try entering them one at a time until
you find the one that works with your TV.
you find the one that works with your TV.
To switch to wide mode, see the footnotes below this table for the applicable
code numbers.
code numbers.
*
1
Press WIDE to switch the wide picture mode on or off.
*
2
Press WIDE, then press
2 +/– to select the wide picture mode you want.
*
3
Press WIDE. The menu appears on the TV screen. Then, press
M/m/</, to
select the wide picture you want and press OK.
Tip
• When you set your TV’s code number correctly while the TV is turned on, the TV
• When you set your TV’s code number correctly while the TV is turned on, the TV
turns off automatically.
Notes
• If you enter a new code number, the code number previously entered will be
• If you enter a new code number, the code number previously entered will be
erased.
• If the TV uses a different remote control system from the one programmed to work
with the VCR, you cannot control your TV with the remote commander.
• When you replace the batteries of the remote commander, the code number may
change. Set the appropriate code number every time you replace the batteries.
Manufacturer
Code number
Sony
01*
1
, 02
Akai
68
Ferguson
52
Grundig
10*
1
, 11*
1
Hitachi
24
JVC
33
Loewe
45
Mivar
09, 70
NEC
66
Nokia
15, 16, 69*
3
Panasonic
17*
1
, 49
Philips
06*
1
, 07*
1
, 08*
1
Saba
12, 13
Samsung
22, 23
Sanyo
25
Sharp
29
Telefunken
36
Thomson
43*
2
Toshiba
38
Manufacturer
Code number
Getti
ng Sta
rted
15
Connecting the VCR
Step 3 : Connecting the VCR
If your TV has a Scart (EURO-AV) connector, see page 16.
If your TV does not have a Scart (EURO-AV) connector
Note
• When you connect the VCR and your TV only with an aerial cable, you have to
• When you connect the VCR and your TV only with an aerial cable, you have to
tune your TV to the VCR (see page 19).
1
Disconnect the aerial cable from
your TV and connect it to
AERIAL IN on the rear panel of
the VCR.
your TV and connect it to
AERIAL IN on the rear panel of
the VCR.
2
Connect AERIAL OUT of the
VCR and the aerial input of your
TV using the supplied aerial cable.
VCR and the aerial input of your
TV using the supplied aerial cable.
3
Connect the mains lead to the mains.
Mains lead
AERIAL IN
to mains
Aerial cable (supplied)
AERIAL OUT
: Signal flow
AERIAL IN
AERIAL
ANTENNE
IN
ENTREE
OUT
SORTIE
IN
ENTREE
OUT
SORTIE
AERIAL
ANTENNE
continued
Click on the first or last page to see other SLV-SE610A / SLV-SE610B / SLV-SE610E / SLV-SE610G / SLV-SE610K / SLV-SE610N / SLV-SE710B / SLV-SE710D / SLV-SE710E / SLV-SE710G / SLV-SE710I / SLV-SE710K / SLV-SE710N / SLV-SE810B / SLV-SE810D / SLV-SE810E / SLV-SE810G / SLV-SE810K / SLV-SE810N / SLV-SX71 service manuals if exist.