SLV-SE350K, SLV-SE500K, SLV-SE500R, SLV-SE600A, SLV-SE600B, SLV-SE600E, SLV-SE600N, SLV-SE650D, SLV-SE700B, SLV-SE700D1, SLV-SE700D2, SLV-SE700E1, SLV-SE700E2, SLV-SE700G, SLV-SE700I, SLV-SE700K, SLV-SE700N, SLV-SE700R, SLV-SE800B, SLV- - Sony VCR Service Manual (repair manual). Page 2

Read Sony SLV-SE350K / SLV-SE500K / SLV-SE500R / SLV-SE600A / SLV-SE600B / SLV-SE600E / SLV-SE600N / SLV-SE650D / SLV-SE700B / SLV-SE700D1 / SLV-SE700D2 / SLV-SE700E1 / SLV-SE700E2 / SLV-SE700G / SLV-SE700I / SLV-SE700K / SLV-SE700N / SLV-SE700R / SLV-SE800B / SLV- Service Manual online

– 2 –
SAFETY CHECK-OUT
1. Check the area of your repair for unsoldered or poorly-sol-
dered connections.  Check the entire board surface for solder
splashes and bridges.
2. Check the interboard wiring to ensure that no wires are
“pinched” or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly transis-
tors, that were installed during a previous repair.  Point them
out to the customer and recommend their replacement.
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer:
4. Look for parts which, though functioning, show obvious signs
of deterioration.  Point them out to the customer and recom-
mend their replacement.
5. Check the B+ voltage to see it is at the values specified.
SAFETY-RELATED  COMPONENT  WARNING!!
COMPONENTS  IDENTIFIED  BY  MARK  
0
  OR  DOTTED
LINE  WITH  MARK  
0
  ON  THE  SCHEMATIC  DIAGRAMS
AND  IN  THE  PARTS  LIST  ARE  CRITICAL  TO  SAFE
OPERATION.  REPLACE  THESE  COMPONENTS  WITH
SONY  PARTS  WHOSE  PART  NUMBERS  APPEAR  AS
SHOWN  IN  THIS  MANUAL  OR  IN  SUPPLEMENTS  PUB-
LISHED  BY  SONY.
SPECIFICATIONS
System
Channel coverage
SLV-SE350K, SE500K/R, SE600N,
  SE700N/K/R, SE800N/K:
PAL (B/G, D/K)
VHF E2 to E12, R1 to R12
UHF E21 to E69, R21 to R69
CATV S1 to S41, S01 to S05
SLV-SE600A/E, SX600E, SE650D,
  SE700D1/D2/E1/E2, SX700D/E,
  SE800D1/D2/E, SX800D:
PAL (B/G)
VHF E2 to E12
VHF Italian channel A to H
UHF E21 to E69
CATV S01 to S05, S1 to S20
HYPER S21 to S41
SLV-SE600B, SE700B, SX700B, SE800B:
SECAM (L)
VHF F2 to F12
UHF F21 to F69
CATV B to Q
HYPER S21 to S41
PAL (B/G)
VHF E2 to E12
VHF Italian channel A to H
UHF E21 to E69
CATV S01 to S05, S1 to S20
HYPER S21 to S41
SLV-SE700G/I, SE800G:
PAL (I)
VHF IA to IJ, SA10 to SA13 (SLV-SE700I)
UHF B21 to B69
CATV S01 to S05, S1 to S20 (SLV-SE700I)
HYPER S21 to S41 (SLV-SE700I)
RF output signal
UHF channels 21 to 69
Aerial out
75-ohm asymmetrical aerial socket
Tape speed
SLV-SE350K, SE500K/R, SE600N,
  SE700N/K/R, SE800N/K:
SP: PAL/MESECAM
23.39 mm/s (recording/playback)
NTSC 33.35 mm/s (playback only)
LP: PAL/MESECAM
11.70 mm/s (recording/playback)
NTSC 16.67 mm/s (playback only)
EP: NTSC 11.12 mm/s (playback only)
SLV-SE600A/E, SX600E, SE650D,
  SE700D1/D2/E1/E2/G/I, SX700D/E,
  SE800D1/D2/E/G, SX800D:
SP: PAL
23.39 mm/s (recording/playback)
NTSC 33.35 mm/s (playback only)
LP: PAL
11.70 mm/s (recording/playback)
NTSC 16.67 mm/s (playback only)
EP: NTSC 11.12 mm/s (playback only)
SLV-SE600B, SE700B, SX700B, SE800B:
SP: PAL
23.39 mm/s (recording/playback)
NTSC
33.35 mm/s (playback only)
SECAM
23.39 mm/s (recording/playback)
MESECAM
23.39 mm/s (playback only)
LP: PAL
11.70 mm/s (recording/playback)
NTSC
16.67 mm/s (playback only)
SECAM
11.70 mm/s (recording/playback)
MESECAM
11.70 mm/s (playback only)
EP: NTSC
11.12 mm/s (playback only)
Page of 94
Display

Click on the first or last page to see other SLV-SE350K / SLV-SE500K / SLV-SE500R / SLV-SE600A / SLV-SE600B / SLV-SE600E / SLV-SE600N / SLV-SE650D / SLV-SE700B / SLV-SE700D1 / SLV-SE700D2 / SLV-SE700E1 / SLV-SE700E2 / SLV-SE700G / SLV-SE700I / SLV-SE700K / SLV-SE700N / SLV-SE700R / SLV-SE800B / SLV- service manuals if exist.