Read Sony SLV-SE100A1 / SLV-SE100A2 / SLV-SE100K / SLV-SE200G / SLV-SE200I / SLV-SE200V1 / SLV-SE200V2 / SLV-SE250B / SLV-SE250D / SLV-SE250P / SLV-SE300D1 / SLV-SE300D2 / SLV-SE300G / SLV-SE400K / SLV-SE450B / SLV-SE450D / SLV-SE450K / SLV-SE450P / SLV-SX100K / SL Service Manual online
— 2 —
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
0
OR DOTTED LINE WITH
MARK
0
ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
1.
Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.
connections. Check the entire board surface for solder splashes
and bridges.
2.
Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
"pinched" or contact high-wattage resistors.
3.
Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
4.
Look for parts which, through functioning, show obvious signs
of deterioration. Point them out to the customer and
recommend their replacement.
of deterioration. Point them out to the customer and
recommend their replacement.
5.
Check the B+ voltage to see it is at the values specified.
6.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
Inputs and outputs
iLINE-1 (TV)
21-pin
Video input: pin 20
Audio input: pins 2 and 6
Audio input: pins 2 and 6
Video output: pin 19
Audio output: pins 1 and 3
Audio output: pins 1 and 3
21-pin
Video input: pin 20
Audio input: pins 2 and 6
Audio input: pins 2 and 6
21-pin
Video input: pin 20
Audio input: pins 2 and 6
Audio input: pins 2 and 6
General
Power requirements
220 – 240 V AC, 50 Hz
Power consumption
18 W
Operating temperature
5
°
C to 40
°
C
Storage temperature
–20
°
C to 60
°
C
Dimensions
Ap
(Approx. 14
×
3 /
8
×
11
/
4
inches)
prox. 355
×
96
×
285 mm (w/h/d)
including projecting parts and controls
Mass
Approx. 3.6 kg (Approx. 7 lb 15 oz.)
Supplied accessories
Remote commander (1)
R6 (size AA) batteries (2)
Aerial cable (1)
Aerial cable (1)
Design and specifications are subject to change without
notice.
notice.
LINE-2 IN
VIDEO IN, phono jack (1)
Input signal: 1 Vp-p, 75 ohms, unbalanced, sync
negative
AUDIO IN, phono jack (1)
Input signal: 1 Vp-p, 75 ohms, unbalanced, sync
negative
AUDIO IN, phono jack (1)
Input level: 327 mVrms
Input impedance: more than 47 kilohms
Input impedance: more than 47 kilohms
SLV-SE250B/D/P, SE450B/D/P, SX250D:
DECODER/tLINE-2 IN
DECODER/tLINE-2 IN
21-pin
Video input: pin 20
Audio input: pins 2 and 6
Audio input: pins 2 and 6
SLV-SE300D1/D2:
DECODER/tLINE-3 IN
DECODER/tLINE-3 IN
SLV-SE300D1/D2/G:
LINE-3 IN
SLV-SE300G:
7
1
Click on the first or last page to see other SLV-SE100A1 / SLV-SE100A2 / SLV-SE100K / SLV-SE200G / SLV-SE200I / SLV-SE200V1 / SLV-SE200V2 / SLV-SE250B / SLV-SE250D / SLV-SE250P / SLV-SE300D1 / SLV-SE300D2 / SLV-SE300G / SLV-SE400K / SLV-SE450B / SLV-SE450D / SLV-SE450K / SLV-SE450P / SLV-SX100K / SL service manuals if exist.