Read Sony SLV-KS1 Service Manual online
6-1
SECTION 6
ADJUSTMENTS
1
2
3
4
Mode
SP
SP
EP
EP
Video signal
Color bar
Monoscope
Color bar
Monoscope
Audio signal
(HiFi/Normal)
400 Hz
Time
Seven minutes
Three minutes
Seven minutes
Three minutes
6-1. MECHANICAL ADJUSTMENTS
Refer to the SERVICE MANUAL of VHS MECHANICAL AD-
JUSTMENT VI.
JUSTMENT VI.
6-2. ELECTRICAL ADJUSTMENTS
2-1.
PRE-ADJUSTMENT PREPARATIONS
Necessary items and indications for total adjustment of electric
circuit of this machine will be described in this chapter.
circuit of this machine will be described in this chapter.
2-1-1.
Instruments to be Used
1) Color TV
2) Oscilloscope 1 or 2 phenomena, band more than 30 MHz, de-
2) Oscilloscope 1 or 2 phenomena, band more than 30 MHz, de-
lay mode, as provided.
3) NTSC pattern generator
4) Digital voltmeter
5) Remote commander
4) Digital voltmeter
5) Remote commander
RMT-V266A (1-418-694-11) or
RMT-V266B (1-418-695-11)
RMT-V266B (1-418-695-11)
6) Audio level meter
7) Audio generator
8) Attenuator
9) Alignment tape
7) Audio generator
8) Attenuator
9) Alignment tape
Part Code: 8-192-605-32 KRV-51N2
2-1-2.
Connection
Unless otherwise specified, connect and adjust the measuring in-
struments as shown in the following diagram.
struments as shown in the following diagram.
During the adjustment, see the Parts Arrangement
Diagram for Adjustments on Page 6-4.
Diagram for Adjustments on Page 6-4.
Fig. 6-2-2
2-1-4.
Alignment Tapes
[Alignment Tape (KRV-51N2)]
2-1-3.
Set-up of Adjustment
In this adjustment, NTSC pattern generator is connected with LINE
input signal terminal. When check to tuner, connected AERIAL
terminal. Check that the amplitudes of video signal SYNC signal,
of picture portions, and of burst signals are flat at approximately
0.3, 0.7 and 0.3 V, respectively, and that the level ratio of the burst
signal and “red” signal are 0.30: 0.66. Fig. 6-2-2. shows video signals
(color bars) used in adjusting the video section.
input signal terminal. When check to tuner, connected AERIAL
terminal. Check that the amplitudes of video signal SYNC signal,
of picture portions, and of burst signals are flat at approximately
0.3, 0.7 and 0.3 V, respectively, and that the level ratio of the burst
signal and “red” signal are 0.30: 0.66. Fig. 6-2-2. shows video signals
(color bars) used in adjusting the video section.
Video output
(75
Ω
)
Pattern generator
VCR
VIDEO LINE IN
Monitor TV
VIDEO LINE OUT
SLV-KS1
2-1-5.
Specified I/O Level and Impedance
Input/output terminal
Video inputs
LINE IN
: phono jack
Input signal : 1 Vp-p, 75
Ω
, unbalanced, sync
negative
Audio inputs
LINE IN
: phono jack
Input level
: 327 mVrms
Input impedance: more than 47 k
Ω
Video outputs
LINE OUT
: phono jack
Output signal : 1 Vp-p, 75
Ω
, unbalanced, sync
negative
Audio outputs
LINE OUT
: phono jacks
Standard output : 327 mVrms
Load impedance : 47 k
Load impedance : 47 k
Ω
Output impedance : less than 10 k
Ω
Fig. 6-2-1
Click on the first or last page to see other SLV-KS1 service manuals if exist.