SLV-GA35MK2, SLV-GA36, SLV-GA45AV, SLV-GA55MK2, SLV-GA59, SLV-GF85MK2, SLV-GF86, SLV-SA34 - Sony VCR Service Manual (repair manual). Page 5

Read Sony SLV-GA35MK2 / SLV-GA36 / SLV-GA45AV / SLV-GA55MK2 / SLV-GA59 / SLV-GF85MK2 / SLV-GF86 / SLV-SA34 Service Manual online

1-1
SECTION  1
GENERAL
This section is extracted from SLV-GF86
instruction manual. (3-063-089-11)
SLV-GA35/GA36/GA45/GA55/GA59/GA65/GF85/GF86/SA34
Getting Started
4
Getting Started
Step 1
Unpacking
Check that you have received the following items with the unit:
• 75-ohm coaxial cable with F-type
connectors
• Audio/video cable (3-phono to 3-
phono)
• Remote commander
• R6 (Size AA) batteries
Getting Started
5
Getting Started
Step 2
Setting up the remote commander
Inserting the batteries
Insert two R6 (size AA) batteries by
matching the + and – on the batteries to
the diagram inside the battery
compartment.
Insert the negative (–) end first, then push
in and down until the positive (+) end
clicks into position.
Using the remote commander
You can use this remote
commander to operate the unit
and a Sony TV. To operate this
unit, point at the remote sensor
on the unit. To operate the TV,
point at the remote sensor on
the TV. Buttons in the shaded
area of the remote commander
can be used to operate your
Sony TV. If the TV does not
have the g symbol near the
remote sensor, this remote
commander will not operate
the TV.
Notes
• With normal use, the batteries should last about three to six months.
• If you do not use the remote commander for an extended period of time, remove
the batteries to avoid possible damage from battery leakage.
• Do not use a new battery with an old one.
• Do not use different types of batteries.
To
Turn the TV to standby or active mode
Turn on the TV power
Increase (+) or decrease (–) the TV volume
Change the TV program position
Select an input source of the TV either from antenna
in or from line in
Press
?/1 (power)
a (TV power)
VOL +/–
PROG (CH) +/–
TV/VIDEO
Remote sensor
a (TV power)
?/1
(on/standby)
TV/VIDEO
PROG (CH) +/–
VOL +/–
Getting Started
6
Step 3
Hookups
Selecting the hookup
There are basically two ways to hook up this unit depending on whether
your TV has audio/video inputs or not.
If your TV has audio/video inputs
See “Audio/video (A/V) hookup” on page 7.
If your TV does not have audio/video inputs
See “Antenna hookup” on pages 8 and 9.
Before you get started
• Turn off the power to all equipment.
• Do not connect the AC power cords until all of the connections are
completed.
• Be sure you make connections firmly.  Loose connections may cause
picture distortion.
• If your TV does not match any of the examples provided, see your nearest
Sony dealer or qualified technician.
Getting Started
7
Getting Started
 Audio/video (A/V) hookup
If your TV has audio/video (A/V) input jacks, you will get a better picture
and sound if you hook up your unit using these connections.
You should also connect the audio outputs of your unit or TV to your stereo
system for a true “home theater” experience.
If your TV does not have A/V inputs, see page 8 for antenna hookup.
A  Use this hookup if your TV has stereo jacks
B  Use this hookup if your TV does not have stereo jacks
This unit
Stereo receiver
TV
TV
This unit
Stereo receiver
Video cable (not supplied)
Audio cable (not supplied)
Audio/video cable (supplied)
continued
IN
VIDEO
AUDIO
AUDIO OUT
AUX IN
AUDIO VIDEO
LINE 1 IN
LINE 1 OUT
AUDIO VIDEO
LINE 1 IN
LINE 1 OUT
VIDEO
AUDIO
IN
AUX IN
Page of 57
Display

Click on the first or last page to see other SLV-GA35MK2 / SLV-GA36 / SLV-GA45AV / SLV-GA55MK2 / SLV-GA59 / SLV-GF85MK2 / SLV-GF86 / SLV-SA34 service manuals if exist.