Read Sony SLV-ED343ME / SLV-ED343SG / SLV-ED949ME / SLV-ED949SG / SLV-EZ141AZ / SLV-EZ745AZ / SLV-GA59ME / SLV-GA59SG Service Manual online
— 2 —
SAFETY CHECK-OUT
1. Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.
and bridges.
2. Check the interboard wiring to ensure that no wires are
“pinched” or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly transistors,
that were installed during a previous repair. Point them out to
the customer and recommend their replacement.
the customer and recommend their replacement.
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer:
safety checks before releasing the set to the customer:
4. Look for parts which, though functioning, show obvious signs
of deterioration. Point them out to the customer and recommend
their replacement.
their replacement.
5. Check the B+ voltage to see it is at the values specified.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
0
OR DOTTED
LINE WITH MARK
0
ON THE SCHEMATIC DIAGRAMS
AND IN THE PARTS LIST ARE CRITICAL TO SAFE
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ED343ME/ED343SG/ED949ME/ED949SG/
EZ141AZ/EZ745AZ:
LINE IN 1/LINE-2 IN
VIDEO IN, phono jack (1)
Input signal: 1 Vp-p, 75 ohms,
unbalanced, sync negative
AUDIO IN, phono jack (2)
Input level: 327 mVrms
Input impedance: more than 47 kilohms
LINE OUT
VIDEO OUT, phono jack (1)
Output signal: 1 Vp-p, 75 ohms,
unbalanced, sync negative
AUDIO OUT, phono jack (2)
Standard output: 327 mVrms
Load impedance: 47 kilohms
Output impedance: less than 10 kilohms
General
Power requirements
ED343ME/ED343SG/ED949ME/ED949SG/
GA59ME/GA59SG:
GA59ME/GA59SG:
110 – 240 V AC, 50/60 Hz
EZ141AZ/EZ745AZ:
220 – 240 V AC, 50 Hz
Power consumption
GA59ME/GA59SG:
10 W
ED343ME/ED343SG/EZ141AZ:
15 W
1.2 W (POWER SAVE is set to ON, minimum)
ED949ME/ED949SG/EZ745AZ:
17 W
1.2 W (POWER SAVE is set to ON, minimum)
Power back-up
ED343ME/ED343SG/ED949ME/ED949SG:
Back-up duration: up to 24 hrs. at a time
EZ141AZ/EZ745AZ:
Back-up duration: up to 6 hrs. at a time
Operating temperature
5 °C to 40 °C
Storage temperature
–20 °C to 60 °C
Dimensions including projecting parts and controls
(w/h/d)
GA59ME/GA59SG:
Approx. 360
×
95
×
245 mm
ED343ME/ED343SG/EZ141AZ:
Approx. 360
×
95
×
255 mm
ED949ME/ED949SG/EZ745AZ:
Approx. 430
×
96
×
255 mm
Mass
ED343ME/ED343SG/GA59ME/GA59SG/
EZ141AZ:
EZ141AZ:
Approx. 2.8 kg
ED949ME/ED949SG/EZ745AZ:
Approx. 3.1 kg
Supplied accessories
Remote commander (1)
R6 (size AA) batteries (2)
ED343ME/ED343SG/ED949ME/ED949SG/
EZ141AZ/EZ745AZ:
EZ141AZ/EZ745AZ:
Aerial cable (1)
GA59ME/GA59SG:
75-ohm coaxial cable with F-type connector (1)
Design and specifications are subject to change without
notice.
Click on the first or last page to see other SLV-ED343ME / SLV-ED343SG / SLV-ED949ME / SLV-ED949SG / SLV-EZ141AZ / SLV-EZ745AZ / SLV-GA59ME / SLV-GA59SG service manuals if exist.