Read Sony SLV-ED333ME / SLV-ED333SG / SLV-ED939ME / SLV-ED939SG / SLV-EZ131AZ / SLV-EZ735AZ / SLV-EZ737AZ / SLV-GA58ME / SLV-GA58SG Service Manual online
GA58ME/GA58SG:
EZ737AZ:
and bridges.
the customer and recommend their replacement.
safety checks before releasing the set to the customer:
their replacement.
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
GA58ME/GA58SG:
EZ131AZ:
EZ131AZ/EZ735AZ/EZ737AZ:
◆ How to eject the cassette tape
into housing ass’y) ································································· 4
Step 1 : Unpacking ····························································· 1-2
Step 2 : Setting up the remote commander ························· 1-2
Step 3 : Connecting the VCR ············································· 1-3
Step 4 : Setting up the VCR with the Auto
Step 6 : Selecting the TV system ········································ 1-5
Presetting channels ················································ 1-5
Changing/disabling programme positions ············· 1-6
Recording TV programmes ················································ 1-8
Recording TV programmes using the Easy Timer ············· 1-9
Recording TV programmes using the timer ····················· 1-10
Setting the recording duration time ·································· 1-11
Checking/changing/cancelling timer settings ··················· 1-11
Recording stereo and bilingual programmes ···················· 1-12
Searching using the index function ·································· 1-13
Adjusting the picture ························································ 1-13
Reducing the VCR’s power consumption ························ 1-13
Changing menu options ···················································· 1-13
Basic editing ····································································· 1-14
Index ················································································· 1-16
2-1-2 Cover Bottom ····································································· 2-1
2-1-3 Ass’y-Panel Front ······························································· 2-2
2-1-4 Ass’y Main PCB, Deck ······················································ 2-3
2-2
2-2-2 Cover Bottom ····································································· 2-4
2-2-3 Ass’y-Panel Front ······························································· 2-5
2-2-4 Ass’y Jack PCB ·································································· 2-5
2-2-5 Ass’y Main PCB, Deck ······················································ 2-6
4-1
4-11 LED Signal Display (GA58) ············································ 4-25
5-1-2 Test point location for adjustment mode setting
5-2-2 ACE Head Position (X-Point) Adjustment ························· 5-4
5-3
6-1-2 Instrument Assembly (Hi-Fi Models) ································· 6-3
6-1-3 Mechanical Parts (Top Side) ·············································· 6-4
6-1-4 Mechanical Parts (Bottom Side) ········································· 6-5
6-2
(If the unit does not operate on condition that tape is inserted into housing ass’y)
(Other method ; Remove the screw of Motor Load Ass’y, Separate the Motor Load Ass’y)
2) When Slider S, T are approached in the position of unloading, rotate holder Clutch counterclockwise after inserting screw driver in the
hole of frame’s bottom in order to wind the unwiunded tape. (Refer to Fig. 3)
(If you rotate Gear Worm 1 continuously when tape is in state of unwinding, you may cause a tape contamination by grease and
tape damage. Be sure to wind the unwiunded tape in the state of set horizontally.)
3) Rotate Gear Worm 1 clockwise using screw driver again up to the state of eject mode and then pick out the tape. (Refer to Fig. 2)