Read Sony SLV-D973PE / SLV-D983PD / SLV-D983PGI Service Manual online
1-2
10
Setting up the remote commander
Step 2 : Setting up the remote commander
Inserting the batteries
Insert two R6 (size AA) batteries by
matching the + and – on the batteries to the
diagram inside the battery compartment.
matching the + and – on the batteries to the
diagram inside the battery compartment.
Insert the negative (–) end first, then push in
and down until the positive (+) end clicks
into position.
and down until the positive (+) end clicks
into position.
Reattach the cover after inserting the battery.
Using the remote commander
You can use this remote commander to
operate this DVD-VCR and a Sony TV.
Buttons on the remote commander marked
with a dot (•) can be used to operate your
Sony TV.
If the TV does not have the
operate this DVD-VCR and a Sony TV.
Buttons on the remote commander marked
with a dot (•) can be used to operate your
Sony TV.
If the TV does not have the
symbol near
the remote sensor, this remote commander
will not operate the TV.
will not operate the TV.
To operate
Set TV / DVD·VIDEO switch to
the DVD player
DVD·VIDEO, then press SELECT DVD and point at the remote sensor at the
DVD-VCR
DVD-VCR
the VCR
DVD·VIDEO, then press SELECT VIDEO and point at the remote sensor at the
DVD-VCR
DVD-VCR
your TV
TV and point at the remote sensor at your TV
Remote sensor
TV / DVD·VIDEO
switch
switch
SELECT VIDEO
SELECT DVD
Getti
ng Sta
rted
11
Setting up the remote commander
Notes
• With normal use, the batteries should last about three to six months.
• If you do not use the remote commander for an extended period of time, remove the batteries
• If you do not use the remote commander for an extended period of time, remove the batteries
to avoid possible damage from battery leakage.
• Do not use a new battery with an old one.
• Do not use different types of batteries.
• Do not leave the remote commander in an extremely hot or humid place.
• Do not drop any foreign object into the remote casing, particularly when replacing the batteries.
• Do not expose the remote sensor to direct light from the sun or lighting apparatus. Doing so
• Do not use different types of batteries.
• Do not leave the remote commander in an extremely hot or humid place.
• Do not drop any foreign object into the remote casing, particularly when replacing the batteries.
• Do not expose the remote sensor to direct light from the sun or lighting apparatus. Doing so
may cause a malfunction.
The remote commander is preprogrammed to control non-Sony TVs. If your TV is listed in the
following table, set the appropriate manufacturer’s code number.
following table, set the appropriate manufacturer’s code number.
Now you can use the buttons with an orange dot (•) to control your TV.
When the TV / DVD·VIDEO switch is set to TV, the remote performs the following:
When the TV / DVD·VIDEO switch is set to TV, the remote performs the following:
* for Sony TV only
Controlling TVs with the remote commander
1
Set TV / DVD·VIDEO switch at the top of the remote commander to TV.
2
Hold down
?/1, and enter your TV’s code number using the number buttons. Then release
?/1.
Buttons
Operations
?/1
Turns your TV on or off
VOL +/–
Adjusts the volume of your TV
PROG +/–
Selects the channel on your TV
Number buttons and
-/--
*
Selects the channel on a Sony TV
MUTING*
Mutes a Sony TV equipped with the muting function
TV/VIDEO
Switches your TV’s input source
continued
12
Setting up the remote commander
Code numbers of controllable TVs
If more than one code number is listed, try entering them one at a time until you find
the one that works with your TV.
the one that works with your TV.
Notes
• If you enter a new code number, the code number previously entered will be erased.
• If the TV uses a different remote control system from the one programmed to work with the
• If the TV uses a different remote control system from the one programmed to work with the
DVD-VCR, you cannot control your TV with the remote commander.
• When you replace the batteries of the remote commander, the code number may change. Set
the appropriate code number every time you replace the batteries.
Manufacturer
Code number
Sony
01 (default), 02
Akai
68
Ferguson
52
Grundig
10, 11
Hitachi
24
JVC
33
Loewe
45
Mivar
09, 70
NEC
66
Nokia
15, 16, 69
Panasonic
17, 49
Philips
06, 07, 08
Saba
12, 13
Samsung
22, 23
Sanyo
25
Sharp
29
Telefunken
36
Thomson
43
Toshiba
38
Manufacturer
Code number
Getti
ng Sta
rted
13
Connecting the DVD-VCR
Step 3 : Connecting the DVD-VCR
For connecting the DVD-VCR, antenna and your TV, select one of the following patterns
A or B, according to the input jack on your TV.
Tip
• “Advanced Hookups” (page 27) explains additional hookup methods that will optimize the
picture and sound for a true “hometheatre” experience.
Note
• You cannot connect the DVD-VCR to a TV that does not have a SCART or video input jack.
A
Use this hookup if your TV has an audio/video connector
1
Disconnect the aerial cable from your TV and
connect it to
connect it to
on the rear panel of the DVD-
VCR.
2
Connect
of the DVD-VCR and the aerial
input of your TV using the supplied aerial
cable.
cable.
3
Connect OUT AUDIO L/R VIDEO jacks of
the DVD-VCR and audio/video connector of
your TV using an audio/video cord.
the DVD-VCR and audio/video connector of
your TV using an audio/video cord.
4
Connect the mains lead to the mains.
If you connect additional equipments to the DVD-VCR (page 15, 27, 29), be
sure to connect the mains lead after all connections are completed.
sure to connect the mains lead after all connections are completed.
Mains lead
AERIAL IN
to mains
Aerial cable (supplied)
: Signal flow
Audio/video cord
(not supplied)
(not supplied)
Audio/video
inputs
continued
Click on the first or last page to see other SLV-D973PE / SLV-D983PD / SLV-D983PGI service manuals if exist.