Read Sony GV-HD700 Service Manual online
4-2
4-2. SCHEMATIC DIAGRAMS
4-2. SCHEMATIC DIAGRAMS
GV-HD700/HD700E_L3
(For schematic diagrams)
• All capacitors are in
• All capacitors are in
µ
F unless otherwise noted. pF :
µ
µ
F. 50 V or less are not indicated except for electrolytics
and tantalums.
• Chip resistors are 1/10 W unless otherwise noted.
k
Ω
=1000
Ω
, M
Ω
=1000 k
Ω
.
• Caution when replacing chip parts.
New parts must be attached after removal of chip.
Be careful not to heat the minus side of tantalum
capacitor, Because it is damaged by the heat.
Be careful not to heat the minus side of tantalum
capacitor, Because it is damaged by the heat.
• Some chip part will be indicated as follows.
Example
C541
L452
22U
10UH
TA A
2520
• Constants of resistors, capacitors, ICs and etc with XX
indicate that they are not used.
In such cases, the unused circuits may be indicated.
In such cases, the unused circuits may be indicated.
• Parts with
★
differ according to the model/destination.
Refer to the mount table for each function.
• All variable and adjustable resistors have characteristic
curve B, unless otherwise noted.
• Signal name
XEDIT
→
EDIT
PB/XREC
→
PB/REC
•
2
: non flammable resistor
•
5
: fusible resistor
•
C
: panel designation
•
A
: B+ Line
•
B
: B– Line
•
J
: IN/OUT direction of (+,–) B LINE.
•
C
: adjustment for repair.
(Measuring conditions voltage and waveform)
• Voltages and waveforms are measured between the
measurement points and ground. They are reference
values and reference waveforms.
(VOM of DC 10 M
values and reference waveforms.
(VOM of DC 10 M
Ω
input impedance is used)
• Voltage values change depending upon input
impedance of VOM used.)
1. Connection
2. Adjust the distance so that the output waveform of
Fig. a and the Fig. b can be obtain.
When indicating parts by reference number, please
include the board name.
include the board name.
Kinds of capacitor
Case size
External dimensions (mm)
THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS
(In addition to this, the necessary note is printed in each block)
(In addition to this, the necessary note is printed in each block)
The components identified by mark
0
or dotted line with
mark
0
are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque
0
sont
critiques pour la sécurité.
Ne les remplacer que par une pièce portant le numéro
spécifie.
Ne les remplacer que par une pièce portant le numéro
spécifie.
ENGLISH
JAPANESE
ENGLISH
JAPANESE
4-2. SCHEMATIC DIAGRAMS
(ENGLISH)
(ENGLISH)
Pattern
Generator
Generator
Video out (75
Ω
)
VIDEO IN
GV-HD700
/HD700E
/HD700E
For NTSC model
For PAL model
Color bar signal waveform
Color bar signal waveform
1 V
0.714 V
0.286 V
White (75%)
White (100%)
Yellow
Cyan
Yellow
Cyan
Green
Magenta
Red
Blue
Burst signal
0.286 V
Q
I
Horizontal sync signal
Horizontal sync signal
1 V
0.7 V
0.3 V
White (100%)
Green
Magenta
Red
Blue
Burst signal
0.3 V
Click on the first or last page to see other GV-HD700 service manuals if exist.