Read Sony KV-DZ29M30 Service Manual online
– 4 –
KV-DZ29M30/M61/M91
RM-GA002
2 OCP:
0
3 OVP:
0
4 VSTOP:
0
5 AKB:
0
8 SOP:
0
9 SOPBT:
0
01 WDT:
N/A
Numeral "0" means that no fault has been detected.
Numeral "1" means a fault has been detected.
SELF DIAGNOSTIC
Numeral "2" means two faults have been detected.
IC4301
RGB JUNGLE
CXA2170AQ
OVP
FROM
CRT (IK)
[V] Q6808, R6910
IC001
SYSTEM
SDA
SDA
9V
5V
IC004
MEMORY
IK_IN
H PROT
RED LED
5
24
57
7
6
V PROT
56
[OCP] Q6804, D6821
[H] D6808, D6809
84
14,47,
82
4. SELF DIAGNOSTIC SCREEN DISPLAY
5. HANDLING SELF DIAGNOSTIC SCREEN DISPLAY
6. SELF-DIAGNOSTIC CIRCUIT
[+B overcurrent OCP ]
Occurs when an overcurrent on the +B(135) line is detected by Q6804.
If Q6804 go to ON, the voltage to the pin57 of IC4301 go to "HIGH".
The unit will automatically turn off.
If Q6804 go to ON, the voltage to the pin57 of IC4301 go to "HIGH".
The unit will automatically turn off.
[High voltage protector of Horizontal Deflection]
Occurs when an overvoltage of horizontal pulse is detected by D6809.
If the voltage of anode D6809 and D6843 goes to High, the voltage to pin57
of IC4301 go to "HIGH".
The unit will automatically turn off.
If the voltage of anode D6809 and D6843 goes to High, the voltage to pin57
of IC4301 go to "HIGH".
The unit will automatically turn off.
[+B overvoltage OVP ]
Occurs when an overvoltage on the +B(135) line is detected by D6635 and
Q6606. If Q6606 go to ON, the voltage to pin6 of IC001 go to "HIGH". The
unit will automatically turn off.
Q6606. If Q6606 go to ON, the voltage to pin6 of IC001 go to "HIGH". The
unit will automatically turn off.
[Vertical deflection failure]
Occurs when an absence of the vertical deflection pulse is detected by
Q6808 and R6910. Shut down the power supply.
Q6808 and R6910. Shut down the power supply.
[White balance failure]
If the RGB levels do not balance or become low level within 5 seconds. This
error will be detected by IC4301.
TV will stay on, but there will be no picture.
error will be detected by IC4301.
TV will stay on, but there will be no picture.
[5V/9V failure]
Occurs when 5V/9V is not supplied to Micon (IC001).
No raster will be detected or no picture.
No raster will be detected or no picture.
5
8
No.
Description
Method
1.
Display self diagnostic screen
[Display] t [Channel ] t [Volume ] t [Power / TV]
Note: The above must be performed while TV is on standby mode.
2.
Stop standby flash
i) Turn off power switch on main.
ii) Unplug power cord from the outlet.
ii) Unplug power cord from the outlet.
3.
Clear fault result
In self diagnostic screen, press
[Channel ] t
-
Note: Diagnostic results display on screen is not automatically cleared. Therefore,
clear result after completion of repair.
clear result after completion of repair.
4.
Quit self diagnostic screen
Turn off power switch of remote commander or main unit.
Click on the first or last page to see other KV-DZ29M30 service manuals if exist.