Read Sony KV-BT212M80 (serv.man3) Service Manual online
– 31 –
KV-BT212M80
RM-W101
5. Write into memory by pressing [MUTING] then
-
on
the remote commander.
WIDE MODE (50Hz)
(V-Compression Adjustment)
1. Input SPCB signal.
2. Adjust condition change to WIDE MODE : ON
3. Copy (Item from normal mode 50Hz) all Normal
1. Input SPCB signal.
2. Adjust condition change to WIDE MODE : ON
3. Copy (Item from normal mode 50Hz) all Normal
Mode adjusted data.
NORMAL MODE (60Hz)
1. Input 525/60Hz signal.
2. They can copy 50Hz first.
2. They can copy 50Hz first.
("COPY" under GEOM is set to
1
, then [MUTE] +
-
)
3. Using the
1
and
4
button, select category GEOM
(Service Mode).
4. Raise/lower data using the
3
and
6
buttons to
obtain optimum image.
GEOM :
000
HPOS
Horizontal Shift (HS)
001
HPAR
Horizontal Parallelogram
002
HBOW
Horizontal Bow
003
VLIN
Vertical Linearity
004
VSCR
Vertical Scroll
005
HSIZ
EW Width (EW)
006
EWPW
EW Parabola/Width (PW)
007
UCOP
EW Upper Corner Parabola
008
LCOP
EW Lower Corner Parabola
009
EWTZ
EW Trapezium
010
VSLP
Vertical Slope (VS)
011
VSIZ
Vertical Amplitude
012
SCOR
S-Correction (SC)
013
VPOS
Vertical Shift (VSH)
014
HBL
RGB Blanking Mode
015
WBF
Timing of Wide Blanking (WBF)
016
WBR
Timing of Wide Blanking (WBR)
017
SBL
Service Blanking
018
COPY
Copy the GEOM data to all
50/60Hz NVM area
50/60Hz NVM area
WIDE MODE (60Hz)
(V-Compression Adjustment)
1. Input mono scope signal.
2. Adjust condition change to WIDE MODE : ON
3. "COPY" is set to
1. Input mono scope signal.
2. Adjust condition change to WIDE MODE : ON
3. "COPY" is set to
1
, then [MUTE] +
-
3-5.
PICTURE DISTORTION ADJUSTMENT
H. CENTER ADJUSTMENT (HPOS)
1. Input Monoscope signal.
2. Activate the Service Adjustment Mode.
3. Select the HPOS item with
1. Input Monoscope signal.
2. Activate the Service Adjustment Mode.
3. Select the HPOS item with
1
and
4
.
4. Adjust the value of HPOS with
3
and
6
for the best
vertical center.
5. Press [MUTING] then
-
to save into the memory.
H. SIZE ADJUSTMENT (HSIZ)
1. Input Monoscope signal.
2. Activate the Service Adjustment Mode.
3. Select HSIZ with
1. Input Monoscope signal.
2. Activate the Service Adjustment Mode.
3. Select HSIZ with
1
and
4
.
4. Adjust with
3
and
6
for the best horizontal size.
5. Press [MUTING] then
-
to save into the memory.
V. SIZE ADJUSTMENT (VSIZ)
1. Input Monoscope signal.
2. Activate the Service Adjustment Mode.
3. Select the VSIZ item with
1. Input Monoscope signal.
2. Activate the Service Adjustment Mode.
3. Select the VSIZ item with
1
and
4
.
4. Adjust value of VPOS with
3
and
6
for the best
vertical center.
5. Press [MUTING] then
-
to save into the memory.
V. CENTER ADJUSTMENT (VPOS)
1. Input Monoscope signal.
2. Activate the Service Adjustment Mode.
1. Input Monoscope signal.
2. Activate the Service Adjustment Mode.
Click on the first or last page to see other KV-BT212M80 (serv.man3) service manuals if exist.