Read Sony KV-AZ213M61 Service Manual online
– 8 –
KV-AZ213M61/M81/M83/N60
RM-GA002
CAUTION:
1. Do not overpull the wire during dressing
_> avoid disconnection of wires.
2. Make sure wires are kept away from
sharp edges, heatsinks & other
hight-temperature parts.
1. Do not overpull the wire during dressing
_> avoid disconnection of wires.
2. Make sure wires are kept away from
sharp edges, heatsinks & other
hight-temperature parts.
Legend:
Hook
SECTION 2
WIRE DRESSING
2-1. Mount Caution on A & CV board
2-2. Connector Assy, 5P dressing
A
C
CN801
CV
CV
W70
CV
CV
CN70
CAUTION:
Dress & control mounted wires (Lead Assy, G2 & 200V wire) on
CV board if necessary :
--> ensure wires do not get trapped during solder dip process
--> ensure wires do not get punched by ICT jig (modify ICT jig if applicable)
CV board if necessary :
--> ensure wires do not get trapped during solder dip process
--> ensure wires do not get punched by ICT jig (modify ICT jig if applicable)
CN703:
Ensure Pin 1 is
connected to
orange wire
(200V)
Ensure Pin 1 is
connected to
orange wire
(200V)
W700:
Board-in Lead
Assy, G2
Board-in Lead
Assy, G2
CV
Lead Assy, G2 & 200V wire on CV
C
UL wire P/N 1-923-082-52 on A Board (W068-W069)
For illustration
W068
UL wire
P/N 1-923-082-52
W069
R828
R829
R889
W052
W052
Keep UL wire close to
board surface --> vertical
seam improvement
board surface --> vertical
seam improvement
CAUTION:
1) Make sure wires are
kept away from sharp
edges & heatsinks
2) Keep UL wire close
to board surface
3) Make sure wires are
kept away from high-
temperature parts
kept away from sharp
edges & heatsinks
2) Keep UL wire close
to board surface
3) Make sure wires are
kept away from high-
temperature parts
CAUTION :
1) Dress Lead Assy, Jumper
according to the green route.
=>
1) Dress Lead Assy, Jumper
according to the green route.
=>
Ensure
Lead
Assy,
Jumper
is dress away from shield case in
the boxed area.
=>
the boxed area.
=>
Ensure
Lead
Assy,
Jumper
is dress below Conn Assy, 5P
(YUV).
2) Make sure wires are kept away
from sharp edges, heatsinks &
other high-temperature parts
(YUV).
2) Make sure wires are kept away
from sharp edges, heatsinks &
other high-temperature parts
Make sure Conn Assy,
5P
Make sure the Connector Assy,
5P (YUV) is kept close to board
5P (YUV) is kept close to board
Make sure the UL tape is
positioned
at the sharp edge of shield
case to
prevent wire from being
scratched
R121
Lead Assy, Jumper
Keep Lead Assy, Jumper
away from shield case -->
C/M for OSD drift from
RF to Video mode
away from shield case -->
C/M for OSD drift from
RF to Video mode
Connector Assy, 5P & Lead Assy, Jumper go
around shield case & dress with pin wire A021
around shield case & dress with pin wire A021
Conn Assy, 5P
For illustration
Mounted Wire (DIP)
Plug (A/I)
Plug (A/I)
Ensure UL wire does not touch high
temperature resistors R828, R829 & R889
temperature resistors R828, R829 & R889
Click on the first or last page to see other KV-AZ213M61 service manuals if exist.