Read Sony KV-21XE42C Service Manual online
6.2 CIRCUIT BOARD LOCATIONS
IC301, IC521, IC602, D572,
D573, D574, DY, C511,C574
C575, R578, R582, R583, R584,
R585, R586, R625, R626, R634,
R635,T504 (FBT)
D573, D574, DY, C511,C574
C575, R578, R582, R583, R584,
R585, R586, R625, R626, R634,
R635,T504 (FBT)
IC001, IC602, R030,
R626, R632, R633, R635,
R636, R637, R638, R639
R626, R632, R633, R635,
R636, R637, R638, R639
Part replaced (
]
)
• All voltages are in V.
• Voltage is DC with respect to ground unless otherwise
noted.
• Readings are taken with a 10M
• Voltage is DC with respect to ground unless otherwise
noted.
• Readings are taken with a 10M
Ω
digital multimeter.
• Readings are taken with a color-bar signal input.
• Voltage variations may be noted due to normal produc-
tion tolerance.
• Circled numbers are waveform references.
• Voltage variations may be noted due to normal produc-
tion tolerance.
• Circled numbers are waveform references.
•
: B + Line
•
: B - Line
•
m
: signal path
Reference Information
RESISTOR : RN
METAL FILM
: RC SOLID
: FPRD NON FLAMMABLE CARBON
: FUSE NON FLAMMABLE FUSIBLE
: RW
: FPRD NON FLAMMABLE CARBON
: FUSE NON FLAMMABLE FUSIBLE
: RW
NON FLAMMABLE WIREWOUND
: RS
NON FLAMMABLE METAL OXIDE
: RB
NON FLAMMABLE CEMENT
: ADJUSTMENT
RESISTOR
COIL : LF-8L MICRO INDUCTOR
CAPACITOR : TA TANTALUM
CAPACITOR : TA TANTALUM
: PS STYROL
: PP POLYPROPYLENE
: PT MYLAR
: MPS METALIZED
: PP POLYPROPYLENE
: PT MYLAR
: MPS METALIZED
POLYESTER
: MPP METALIZED
POLYPROPYLENE
: ALB BIPOLAR
: ALT HIGH
: ALT HIGH
TEMPERATURE
: ALR HIGH
RIPPLE
- - - - -
Pitch: 5mm
Rating electrical power 1/4W
Rating electrical power 1/4W
• All resistors are in ohms.
K
Ω
=1000
Ω
, M
Ω
=1000K
Ω
•
f
nonflammable resistor.
•
∆
:
internal component.
•
p
: panel designation and adjustment for repair.
• All variable and adjustable resistors have charac-
teristic curve B, unless otherwise noted.
teristic curve B, unless otherwise noted.
• The components identified by
]
in this manual have
been carefully factory-selected for each set in order to
satisfy regulations regarding X-ray radiation. Should
replacement be required, replace only with the value
originally used.
satisfy regulations regarding X-ray radiation. Should
replacement be required, replace only with the value
originally used.
• When replacing components identified by
]
make the
necessary adjustments indicated. If results do not
meet the specified value, change the component
identified by
meet the specified value, change the component
identified by
[
and repeat the adjustment until the
specified value is achieved.
(Refer to R582 on page 21 & 22).
(Refer to R582 on page 21 & 22).
• When replacing parts in the table below be sure to
perform the related adjustment.
perform the related adjustment.
6.3 PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS
Note:
•
•
All capacitors are in
µ
F unless otherwise noted.
pF:
µµ
F 50WV or less are not indicated except
for electrolytic and tantalums.
• All electrolytics are 50V unless otherwise specified
• Indication of resistance, which does not have one for
rating electrical power, is as follows:
• All electrolytics are 50V unless otherwise specified
• Indication of resistance, which does not have one for
rating electrical power, is as follows:
Adjustment (
[
)
HV HOLD-DOWN
(R582)
(R582)
B+ VOLTAGE
CONFIRMATION
CONFIRMATION
Note: The symbol
G
display is on the component side.
The components identified by shading and mark
¡
¡
¡
¡
¡
are
critical for safety. Replace only with part number
specified.
specified.
The symbol
G
indicates fast operating fuse.
Replace only with fuse of same rating as marked.
— 28 — — 29 — — 30 —
— 27 —
SECTION 6
DIAGRAMS
KV-21XE42C
6.1 BLOCK DIAGRAM
870 Block Diagram.p65 6/10/99, 10:28 AM
1
Click on the first or last page to see other KV-21XE42C service manuals if exist.