Read Sony KD-55X9000A Service Manual online
KD-55/65X9000A(CH)
8
SELF DIAGNOSIS FUNCTION
DIAGNOSTIC TEST INDICATORS
When an error occurs, the Smart Core Red LED will flash a set number of times to indicate the possible cause of the problem.
If there is more than one error, the LED will identify the first of the problem areas.
Result for all of the following diagnostic items are displayed on screen.
If the screen displays a “0”, no error has occurred .
The units in this manual contain a self-diagnostic function. If an error occurs, the Smart Core Red LED will automatically begin to flash.
The number of times the LED flashes translates to a probable source of the problem.
A definition of the Smart Core Red LED flash indicators is listed in the instruction manual for the user’s knowledge and reference.
If an error symptom cannot be reproduced, the remote commander can be used to review the failure occurrence data stored in memory to reveal past problems and how often these
problems occur.
The number of times the LED flashes translates to a probable source of the problem.
A definition of the Smart Core Red LED flash indicators is listed in the instruction manual for the user’s knowledge and reference.
If an error symptom cannot be reproduced, the remote commander can be used to review the failure occurrence data stored in memory to reveal past problems and how often these
problems occur.
RED LED blinking count
Detection Items
2x
<G/B> Main 12V failure [MAIN_POWE]
* This failure is not saved.
3x
<B> Main 5.0/3.3/1.8/1.0/ 1.1V failure [DC_ALERT]
* 5.0/1.0V failures are not saved.
<B/S> Audio amp. protection [AUD_PROT]
<B> HDMI equalizer/switch I2C NACK [HDMI_EQ] * There is Temp. sensor on the same I2C bus
<C> HDMI switch/equalizer I2C communication monitoring. [HDMI_EQCX]
<B> Tuner or demodulator I2C NACK [TU_DEMOD]
<B> AFE device I2C NACK [AFE_I2C]
<B> AFE device SPI NACK [AFE_SPI] * only for AEP,CH
<B> HDMI equalizer/switch I2C NACK [HDMI_EQ] * There is Temp. sensor on the same I2C bus
<C> HDMI switch/equalizer I2C communication monitoring. [HDMI_EQCX]
<B> Tuner or demodulator I2C NACK [TU_DEMOD]
<B> AFE device I2C NACK [AFE_I2C]
<B> AFE device SPI NACK [AFE_SPI] * only for AEP,CH
<B> Scorpio VBO Tx Lock monitoring. [SC_OUT_ERR]
<B> VBO Lock monitoring between Ayu2 and Scorpio. [SC_ERR]
<B> Scorpio SPI Flash read error detection. [SC_ERR]
<B> Scorpio device I2C communication error detection. [SC_ERR]
<B> VBO Lock monitoring between Ayu2 and Scorpio. [SC_ERR]
<B> Scorpio SPI Flash read error detection. [SC_ERR]
<B> Scorpio device I2C communication error detection. [SC_ERR]
<B> DDR-PHY DLL ready error detection for FRC. [FRCD_I2C]
<B> DRAM initial sequence done error detection for FRC. [FRCD_I2C]
<B> FRC device I2C communication error detection. [FRCD_I2C]
<B> DRAM initial sequence done error detection for FRC. [FRCD_I2C]
<B> FRC device I2C communication error detection. [FRCD_I2C]
4x
<L/P> LED driver failure/LED voltage protection [LD_ERR]
5x
<P/T/G/B> Panel ID EEPROM I2C NACK (Also panel power failure is a suspect) [P_ID_ERR]
<T> TCON device I2C NACK [TCON_ERR]
<T> TCON device Initialization failure [TCON_ERR]
<T> TCON device Initialization failure [TCON_ERR]
6x
<G/T/P/B> Backlight converter OVP[BACKLITE]
7x
Over temperature protection [TEMP_ERR]
<B> Temp. sensor I2C NACK [TEMP_ERR] * There is HDMI Eq on the same I2C bus.
<B> Temp. sensor I2C NACK [TEMP_ERR] * There is HDMI Eq on the same I2C bus.
8x
Software Error (Also the main board’s memory or CAM module is a suspect)
<G>: Power supply board, <B>: Main board, <T>: Tcon board, <L>: LED driver (LD) board
<P>: Panel module , <S>: Speaker, <A>: Power Adapter, <C>: CX board
<P>: Panel module , <S>: Speaker, <A>: Power Adapter, <C>: CX board
Click on the first or last page to see other KD-55X9000A service manuals if exist.