Read Sony KD-49X8505B / KD-55X8505B / KD-55X9005B / KD-65S9005B / KD-65X8505B / KD-65X9005B / KD-65X9505B / KD-70X8505B / KD-75S9005B / KD-79X9005B / KD-85X9505B / KDL-32W705B / KDL-32W705C / KDL-32W706B / KDL-40W605B / KDL-40W705C / KDL-42W705B / KDL-42W706B / KDL Service Manual online
RB2G / RB2T
CHASSIS
Some user setting may have
changed during the update.
Please remove the USB device and
select ""OK to exit.
Status 1
Status 2
Remove
Remove
1) Replace a panel module (Refer to each segment Service Manual for
Board (Tcon, Driver/ Converter & Panel) details).
2) After AC Plug-in(AC On), wait for 20s then turn on TV by power key on
TV or Remote Commander.
Note : Important: 20s wait is necessary for
successful SW writing in Task [3].
b) When you turn on the TV after replacing Panel , there will be two
cases depend on the PANEL ID setting. Below are the example:
cases depend on the PANEL ID setting. Below are the example:
3)
Software update by USB memory. (refer to section 1.3 Preparing USB for
Upgrade)
i) Remove all signal connection.(antenna, external input, ether cable, etc)
ii) Insert the USB memory.
Upgrade)
i) Remove all signal connection.(antenna, external input, ether cable, etc)
ii) Insert the USB memory.
iii) If older software package version is used, smart core amber and
green LED will remain blinking. (Software can not update).
green LED will remain blinking. (Software can not update).
iv) If valid file found, below message will appear. TV will reboot in a
minute after the USB device is inserted, then the Red LED lights and the
Amber LED blinks
minute after the USB device is inserted, then the Red LED lights and the
Amber LED blinks
13
SERVICE PROCEDURE
( PANEL)
( PANEL)
SERVICE PROCEDURE (PANEL)
SECTION 3
i) Panel : No Picture- SMART CORE LED :
Amber & Green blinking
Amber & Green blinking
ii) Panel : Picture appear
SMART CORE LED : White Lit
SMART CORE LED : White Lit
4) TV on standby. Enter Service Mode. Press “i+ (info)”, “5”, “Volume +” then “TV
power” on remote.
Note : a) <Restriction>When TV power status is "Deep STBY Mode", you
cannot enter Service Mode due to not receive the above SIRCS command.
cannot enter Service Mode due to not receive the above SIRCS command.
b) <Operation method> (To enter this mode surely.)
After TV goes to STBY status by Remote commander, Please input the
sequence (four keys described above) by RC within 15 seconds (UC) or 1
minute (Other Destination).
sequence (four keys described above) by RC within 15 seconds (UC) or 1
minute (Other Destination).
3-1. Service Procedure for Panel Module replacement.
Note :
Black font : Procedure/ Step
Red font : Caution ( Additional Info).
Blue font: Additional Info.
Black font : Procedure/ Step
Red font : Caution ( Additional Info).
Blue font: Additional Info.
Preparing for software update.
During the system update, the TV
will automatically restart.
Please do not disconnect the power or
remove the USB device, until update
is completed.
The update may take up to 5 minutes.
Copying update file from USB.
Please wait...
v) Status 1: Please wait awhile, until the SMART CORE LED will change to white blinking
then TV goes to Standby (Software update complete). Turn on TV. OR
then TV goes to Standby (Software update complete). Turn on TV. OR
v) Status 2: After SW completes, TV will reboot itself and message will appear to
indicate SW update complete/
indicate SW update complete/
Click on the first or last page to see other KD-49X8505B / KD-55X8505B / KD-55X9005B / KD-65S9005B / KD-65X8505B / KD-65X9005B / KD-65X9505B / KD-70X8505B / KD-75S9005B / KD-79X9005B / KD-85X9505B / KDL-32W705B / KDL-32W705C / KDL-32W706B / KDL-40W605B / KDL-40W705C / KDL-42W705B / KDL-42W706B / KDL service manuals if exist.