Read Sony HDR-XR100 / HDR-XR100E / HDR-XR101 / HDR-XR105E / HDR-XR106E / HDR-XR200 / HDR-XR200E / HDR-XR200V / HDR-XR200VE (serv.man2) Service Manual online
1-2
ENGLISH
JAPANESE
ENGLISH
JAPANESE
HDR-XR100/XR100E/XR101/XR105E/XR106E/XR200/XR200E/XR200V/XR200VE_L2
1-3-3. Self-diagnosis Code Table
C
C
C
C
E
E
E
E
E
Block
Function
0
4
1
3
1
3
3
2
2
0
3
1
6
1
6
1
6
1
Detailed
Code
0
0
0
1
0
2
6
0
0
0
0
0
0
0
1
0
1
1
Symptom/State
Non-standard battery is used.
“Memory Stick Duo” is unformatted.
“Memory Stick Duo” is broken.
“Memory Stick Duo” is broken.
Access error
Difficult to adjust focus
(Cannot initialize focus)
(Cannot initialize focus)
Flash memory data are rewritten.
Drive fault
Difficult to adjust focus
(Cannot initialize focus.)
(Cannot initialize focus.)
Zoom operations fault
(Cannot initialize zoom lens.)
(Cannot initialize zoom lens.)
The abnormalities in initialization of
the focus lens and the abnormalities in
initialization of the zoom lens occurred
simultaneously.
the focus lens and the abnormalities in
initialization of the zoom lens occurred
simultaneously.
Self-diagnosis Code
Repaired b
y:
Note:
Start the Adjust Manual in the Adjust Station and refer to the “DESTINATON DATA WRITE”.
Correction
Use the InfoLITHIUM battery.
Format the “Memory Stick Duo”.
Insert a new “Memory Stick Duo”.
Insert a new “Memory Stick Duo”.
Remove the power source.
Reconnect it again and operate your camcorder again.
Reconnect it again and operate your camcorder again.
XR200/XR200E/XR200V/XR200VE:
Retry turn the power on by the power switch. If it does not
recover, check the focus MR sensor of lens block (pin eg, eh of
CN5101 on the LD-244 board). If it is OK, check the focus
motor drive IC (IC5506 on the LD-244 board).
recover, check the focus MR sensor of lens block (pin eg, eh of
CN5101 on the LD-244 board). If it is OK, check the focus
motor drive IC (IC5506 on the LD-244 board).
Make flash memory data correct value. (Note)
Inspect or replacement of the hard disk drive.
XR100/XR100E/XR101/XR105E/XR106E:
Inspect the lens block focus reset sensor (pin 8 of CN5201 on
the LD-245 board) when focusing is performed when the focus
buttons of the touch panel are pressed in the focus manual mode,
and the focus motor driver circuit (IC5206 on the LD-245 board)
when focusing is not performed.
the LD-245 board) when focusing is performed when the focus
buttons of the touch panel are pressed in the focus manual mode,
and the focus motor driver circuit (IC5206 on the LD-245 board)
when focusing is not performed.
XR100/XR100E/XR101/XR105E/XR106E:
Inspect the lens block zoom reset sensor (pin q; of CN5201 on
the LD-245 board) when zooming is performed when the zoom
lever is operated, and the zoom motor drive circuit (IC5206 on
the LD-245 board) when zooming is not performed.
the LD-245 board) when zooming is performed when the zoom
lever is operated, and the zoom motor drive circuit (IC5206 on
the LD-245 board) when zooming is not performed.
XR200/XR200E/XR200V/XR200VE:
Inspect the lens block zoom MR sensor (pin ea, ed of CN5101
on the LD-244 board) when zooming is performed when the
zoom lever is operated, and the zoom motor drive circuit
(IC5506 on the LD-244 board) when zooming is not performed.
on the LD-244 board) when zooming is performed when the
zoom lever is operated, and the zoom motor drive circuit
(IC5506 on the LD-244 board) when zooming is not performed.
XR100/XR100E/XR101/XR105E/XR106E:
Check whether the flexible board of the lens is broken, and
check whether it is inserted imperfectly. If there is no problem in
the flexible board, inspect the focus/zoom motor drive circuit
(IC5206 on the LD-245 board).
check whether it is inserted imperfectly. If there is no problem in
the flexible board, inspect the focus/zoom motor drive circuit
(IC5206 on the LD-245 board).
XR200/XR200E/XR200V/XR200VE:
Check both C : 32 : 60 and E : 61 : 10 of the self-diagnosis code.
Click on the first or last page to see other HDR-XR100 / HDR-XR100E / HDR-XR101 / HDR-XR105E / HDR-XR106E / HDR-XR200 / HDR-XR200E / HDR-XR200V / HDR-XR200VE (serv.man2) service manuals if exist.