Read Sony HDR-SR5 / HDR-SR5C / HDR-SR5E / HDR-SR7 / HDR-SR7E / HDR-SR8 / HDR-SR8E (serv.man4) Service Manual online
6-42
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ
8.
Shift Lens Check
Use the “Shift Lens Check” when the following self diagnostic
codes are displayed.
• E:62:10 [Shift Lens Initializing Failure]
codes are displayed.
• E:62:10 [Shift Lens Initializing Failure]
• E:62:11 [Shift Lens Overheating (Pitch)]
• E:62:12 [Shift Lens Overheating (Yaw)]
Click the [Shift Lens Check] button on the Service Mode screen,
and the “SHIFT LENS CHECK” screen will appear.
and the “SHIFT LENS CHECK” screen will appear.
[Check 1 using method]
Use this menu when E:62:10 (Shift Lens Initializing Failure) oc-
curred.
Click the [Check 1 Start] button, and the “EEPROM Check” and
“Steady Hall Adjustment” will be executed.
• When “Steady Hall Adjustment” is executed, the shift lens will
Use this menu when E:62:10 (Shift Lens Initializing Failure) oc-
curred.
Click the [Check 1 Start] button, and the “EEPROM Check” and
“Steady Hall Adjustment” will be executed.
• When “Steady Hall Adjustment” is executed, the shift lens will
move in up, down, left, and right directions. If the shift lens
does not move at all and a message “Shift Lens Check 1 Com-
plete” is displayed, or if an error message of Steady Hall Ad-
justment is displayed, replace the lens block.
does not move at all and a message “Shift Lens Check 1 Com-
plete” is displayed, or if an error message of Steady Hall Ad-
justment is displayed, replace the lens block.
• Check the peripheral circuits (particularly EEPROM (IC1804))
of the IC1803 on the VC-504 board, when the following mes-
sage is displayed.
sage is displayed.
[Check 2 using method]
Use this menu when E:62:11 (Shift Lens Overheating (Pitch)) oc-
curred.
Click the [Check 2 Start] button, and the shift lens will move in up
and down directions. If the shift lens does not move, replace the
lens block.
Use this menu when E:62:11 (Shift Lens Overheating (Pitch)) oc-
curred.
Click the [Check 2 Start] button, and the shift lens will move in up
and down directions. If the shift lens does not move, replace the
lens block.
[Check 3 using method]
Use this menu when E:62:12 (Shift Lens Overheating (Yaw)) oc-
curred.
Click the [Check 3 Start] button, and the shift lens will move in left
and right directions. If the shift lens does not move, replace the
lens block.
Use this menu when E:62:12 (Shift Lens Overheating (Yaw)) oc-
curred.
Click the [Check 3 Start] button, and the shift lens will move in left
and right directions. If the shift lens does not move, replace the
lens block.
7.
Record Data
Click the [Record Data] button on the SERVICE MODE screen,
and the “RECORD DATA” screen will appear.
and the “RECORD DATA” screen will appear.
The record data such as use record and self-diagnostic record are
displayed.
displayed.
Initializing method (Self-Diagnosis Data Only):
Click the [Clear Self-Diagnosis Data Only] button on the screen, and
the Self-Diagnosis Data will be initialized.
Click the [Clear Self-Diagnosis Data Only] button on the screen, and
the Self-Diagnosis Data will be initialized.
Note:
If a flash error (self-diagnosis code E:91:**) occurred, all
record data must be initialized to reset the error. The error
cannot be reset by initializing the self-diagnosis data only.
record data must be initialized to reset the error. The error
cannot be reset by initializing the self-diagnosis data only.
Initializing method (All Record-Data):
Click the [Clear All Recorded-Data] button on the screen, and the
All Recorded-Data will be initialized.
Click the [Clear All Recorded-Data] button on the screen, and the
All Recorded-Data will be initialized.
Note:
Performing the initialization causes all the user settings in-
cluding time setting to be initialized, too.
cluding time setting to be initialized, too.
Ver. 1.1 2007.10
Click on the first or last page to see other HDR-SR5 / HDR-SR5C / HDR-SR5E / HDR-SR7 / HDR-SR7E / HDR-SR8 / HDR-SR8E (serv.man4) service manuals if exist.