HDR-CX190, HDR-CX190E, HDR-CX200, HDR-CX200E, HDR-CX210, HDR-CX210E, HDR-PJ200, HDR-PJ200E, HDR-PJ210 (serv.man2) - Sony Movie Service Manual (repair manual). Page 8

HDR-CX190/CX190E/CX200/CX200E/CX210/CX210E/PJ200/PJ200E/PJ210_L2

1-4

Self-diagnosis Code

Symptom/State

Correction

Repaired by:

Block

Function

Detailed

Code

E

6

1

1

0

Zoom operations fault
(Cannot initialize zoom lens.)

Inspect the lens block zoom drive signal (pin 1 to 4 of CN1005 on 
the VC-651 board, when zooming is performed when the zoom lever is 
operated, and the zoom motor drive IC (IC5306 on the VC-651 board) 
when zooming is not performed.

E

6

1

1

1

The abnormalities in initialization of the focus 
lens and the abnormalities in initialization of 
the zoom lens occurred simultaneously.

Check both C: 32: 60 and E: 61: 10 of the self-diagnosis code.

E

6

1

3

0

Reset position detection error on the stepper 
iris initializing

Turn the power on to open lens barrier. Disconnect the battery or power 
cord, and then connect again.
Confirm that the iris blades in lens are working.
If iris blades do not working, check the iris motor drive IC in lens drive 
block (CN1005 pin qd to qk on the VC-651 board).
If iris blades work normally, confirm that they are closing completely 
and confirm following item.
･  Case of the iris blades do not close normally Replace the lens block).
･  Case of “E: 61: 30” is appeared and iris blades closed completely.
  Confirm that communication with lens block is normal.
･ Case of LCD is not displayed normally Check that connection 

between CN6805 on the CM-127 board and CN1002 and VC-651 
board by FP-1483 flexible board.

･  Case of LCD is displayed normally Replace the lens block.

E

6

2

0

0

Handshake correction function does not work 
well. (With PITCH angular velocity sensor 
output stopped.)

Inspect PITCH angular velocity sensors (SE7501 on the CM-127 
board) peripheral circuits.

E

6

2

0

1

Handshake correction function does not work 
well. (With YAW angular velocity sensor 
output stopped.)

Inspect YAW angular velocity sensors (SE7501 on the CM-127 board) 
peripheral circuits.

E

6

2

0

2

Abnormality of IC for steadyshot.

Turn power off and turn power on again.

E

6

2

0

3

IC for steadyshot and micro controller com-
munication abnormality among.

Turn power off and turn power on again.

E

6

2

0

4

Image vibration correction during handshake 
function does not work.

Inspect the image vibration angular velocity sensors (SE7501 in the 
CM-127 board) peripheral circuits.

E

6

2

1

0

Shift lens initializing failure.

Replacement of lens block. (Note 3) 
If an error occurs again, replace the VC-651 board.

E

6

2

1

1

Shift lens overheating (Pitch)

Turn power off and turn power on again.

E

6

2

1

2

Shift lens overheating (Yaw)

Turn power off and turn power on again.

E

6

2

2

0

Abnormality of thermistor.

Turn power off and turn power on again.

E

9

1

0

1

Abnormality when flash is beingcharged.

Turn power off and turn power on again.

E

9

1

0

2

Abnormality of LED Video light.

Turn power off and turn power on again.

E

9

1

0

3

Abnormality of LED Video light  Tempera-
ture detection.

Turn power off and turn power on again.

E

9

2

0

1

Battery current value goes over the max 
discharge current

Check the remaining battery power because this symptom maybe 
depended on the remaining battery level, and confirm whether or 
not the symptom is occurred after replacing the battery. If the symp-
tom is still occurred, overhaul inspection is needed. Check each 
output of DC/DC converter (IC4301 on the VC-651 board) on with 
connected the DC JACK (J1001). 
(The minimum connection to periphery)

E

9

4

0

0

Fault of writing or erasing the flash mem-
ory

IM Model:
Inspect the flash memory (IC8101, IC8201 on the MM-102 board).

E

9

4

0

1

Internal flash memory fault

IM Model:
Inspect the flash memory (IC8101, IC8201 on the MM-102 board).

E

9

4

0

2

BGM data error

Check the CPU (IC1301 on the VC-651 board).

*

*

*

*

*

Self-diagnosis Code

Symptom/State

Correction

Repaired by:

Block

Function

Detailed

Code

E

9

5

0

0

GPS hardware error

Turn power off and turn power on again.

E

9

6

0

0

Map area mount error

Turn power off and turn power on again.

E

9

7

0

0

Projector  hardware error

Turn power off and turn power on again.

Note 3: When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.

After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.

Refer to the following flowchart when repairing or inspecting the projector’s projection function.

If you have received an indication on the projector’s projection function from the customer, check defective part according to the following flow-
chart. 
When a defective part has been clarified, repair the projector according to the check result.

Note 1: The projector unit (copper plate in particular) becomes hot after it is used.
 

When replacing a part of the projector unit, wait until it is cooled down.

 

Wipe the lens gently with a soft cloth such as a cleaning cloth or glass cleaning cloth.

Note 2: Stubborn stains may be removed with a soft cloth such as a cleaning cloth or glass cleaning cloth lightly dampened with water.
 

Never use a solvent such as alcohol, benzene or thinner; acid, alkaline or abrasive detergent; or a chemical cleaning cloth, as they will damage the lens sur-
face.

*

*

Indicated defective

projector received

Measure brightness.

(  2)

Yes

No

OK

OK

NG

NG

OK

NG

A

B

Indication on 

brightness

Inspect projector

LED. 

(  1)

  1  Refer to the ADJUST tab of Adjust Manual.
  2  Refer to the SERVICE tab of Adjust Manual.

Inspect projector

LED. 

(  1)

END

-
-
-

-

-

Replace projector unit (light emitting block). (*1)
Replace PJ board. (*1)
Replace both projector unit (light emitting block)
and PJ board. (*1)

Projector Data Input

Fixed value input
Enter the number on the label attached to the unit.

Serial number input
LD40

Syywwnnnnn 

Enter the red part.

(See page 1-5)

(See page 1-5)

The changed portions from
Ver. 1.0 are shown in blue.