Read Sony HDR-CX100 / HDR-CX100E / HDR-CX105E / HDR-CX106E / HDR-CX120 (serv.man2) Service Manual online
1-3
ENGLISH
JAPANESE
ENGLISH
JAPANESE
HDR-CX100/CX100E/CX105E/CX106E/CX120_L2
Correction
Use the InfoLITHIUM battery.
Format the “Memory Stick Duo”.
Insert a new “Memory Stick Duo”.
Insert a new “Memory Stick Duo”.
Remove the power source.
Reconnect it again and operate your camcorder again.
Reconnect it again and operate your camcorder again.
Make flash memory data correct value. (Note 1)
Inspect or replacement of the “INTERNAL MEMORY (MS7304)”
Inspect the lens block focus reset sensor (pin 8 of CN5201 on
the LD-247 board) when focusing is performed when the focus
buttons of the touch panel are pressed in the focus manual mode,
and the focus motor driver circuit (IC5206 on the LD-247 board)
when focusing is not performed.
the LD-247 board) when focusing is performed when the focus
buttons of the touch panel are pressed in the focus manual mode,
and the focus motor driver circuit (IC5206 on the LD-247 board)
when focusing is not performed.
Inspect the lens block zoom reset sensor (pin 0 of CN5201 on
the LD-247 board) when zooming is performed when the zoom
lever is operated, and the zoom motor drive circuit (IC5206 on
the LD-247 board) when zooming is not performed.
the LD-247 board) when zooming is performed when the zoom
lever is operated, and the zoom motor drive circuit (IC5206 on
the LD-247 board) when zooming is not performed.
Check whether the flexible board of the lens is broken, and
check whether it is inserted imperfectly. If there is no problem in
the flexible board, inspect the focus/zoom motor drive circuit
(IC5206 on the LD-247 board).
check whether it is inserted imperfectly. If there is no problem in
the flexible board, inspect the focus/zoom motor drive circuit
(IC5206 on the LD-247 board).
Inspect PITCH/YAW angular velocity sensors (SE6601 on the
JK-386 board) peripheral circuits.
JK-386 board) peripheral circuits.
Inspect PITCH/YAW angular velocity sensors (SE6601 on the
JK-386 board) peripheral circuits.
JK-386 board) peripheral circuits.
Inspect the flash memory (IC2101 on the VC-559 board).
Format the “INTERNAL MEMORY (MS7304)”.
Insert a new “INTERNAL MEMORY (MS7304)”. (Note 2)
Symptom/State
Non-standard battery is used.
“Memory Stick Duo” is unformatted.
“Memory Stick Duo” is broken.
“Memory Stick Duo” is broken.
Access error
Flash memory data are rewritten.
Drive fault
Difficult to adjust focus
(Cannot initialize focus.)
(Cannot initialize focus.)
Zoom operations fault
(Cannot initialize zoom lens.)
(Cannot initialize zoom lens.)
The abnormalities in initialization of
the focus lens and the abnormalities in
initialization of the zoom lens occurred
simultaneously.
the focus lens and the abnormalities in
initialization of the zoom lens occurred
simultaneously.
Handshake correction function does not
work well. (With PITCH angular
velocity sensor output stopped.)
work well. (With PITCH angular
velocity sensor output stopped.)
Handshake correction function does not
work well. (With YAW angular velocity
sensor output stopped.)
work well. (With YAW angular velocity
sensor output stopped.)
Fault of writing to or erasing the flash
memory
memory
“INTERNAL MEMORY” is
unformatted.
“INTERNAL MEMORY” is broken.
unformatted.
“INTERNAL MEMORY” is broken.
1-4-3. Self-diagnosis Code Table
C
C
C
E
E
E
E
E
E
E
E
E
Block
Function
0
4
1
3
1
3
2
0
3
1
6
1
6
1
6
1
6
2
6
2
9
4
9
4
Detailed
Code
0
0
0
1
0
2
0
0
0
0
0
0
1
0
1
1
0
0
0
1
0
0
0
1
Self-diagnosis Code
Repaired b
y:
Note 1:
Start the Adjust Manual in the Adjust Station and refer to the “DESTINATON DATA WRITE”.
Note 2:
Start the Adjust Manual in the Adjust Station and refer to the “INTERNAL MEMORY ADJUSTMENTS”.
Click on the first or last page to see other HDR-CX100 / HDR-CX100E / HDR-CX105E / HDR-CX106E / HDR-CX120 (serv.man2) service manuals if exist.