Read Sony DCR-VX9000E Service Manual online
DCR-VX9000E
RMT-806/807
AEP Model
UK Model
E Model
SERVICE MANUAL
DIGITAL VIDEO CAMERA RECORDER
MICROFILM
L MECHANISM
SPECIFICATIONS
— Continued on next page —
— 2 —
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
!
OR DOTTED LINE
WITH MARK
!
ON THE SCHEMATIC DIAGRAMS AND IN THE
PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE
THESE COMPONENTS WITH SONY PARTS WHOSE PART
NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN
SUPPLEMENTS PUB-LISHED BY SONY.
THESE COMPONENTS WITH SONY PARTS WHOSE PART
NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN
SUPPLEMENTS PUB-LISHED BY SONY.
1.
Check the area of your repair for unsoldered or poorly-
soldered connections. Check the entire board surface for
solder splashes and bridges.
soldered connections. Check the entire board surface for
solder splashes and bridges.
2.
Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
"pinched" or contact high-wattage resistors.
3.
Look for unauthorized replacement parts, par-ticularly
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
4.
Look for parts which, through functioning, show obvious
signs of deterioration. Point them out to the customer and
recommend their replace-ment.
signs of deterioration. Point them out to the customer and
recommend their replace-ment.
5.
Check the B+ voltage to see it is at the values specified.
6.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of
the circuit board (within 3 times).
• Be careful not to apply force on the conductor when
soldering or unsoldering.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
— 3 —
TABLE OF CONTENTS
SERVICE NOTE
·································································· 7
1.
GENERAL
Getting started
Attaching the viewfinder ···················································· 1-1
Charging and installing the battery pack ···························· 1-1
Inserting a cassette ······························································ 1-3
Charging and installing the battery pack ···························· 1-1
Inserting a cassette ······························································ 1-3
Basic operations
Camera recording ································································ 1-4
Hints for better shooting ····················································· 1-7
Checking the recorded picture ············································ 1-8
Connections for playback ··················································· 1-9
Playing back a tape ····························································· 1-10
Hints for better shooting ····················································· 1-7
Checking the recorded picture ············································ 1-8
Connections for playback ··················································· 1-9
Playing back a tape ····························································· 1-10
Advanced operations
Using alternative power sources ········································· 1-12
Changing the mode settings ················································ 1-13
Overlapping two pictures ···················································· 1-15
Using the wide mode function ············································ 1-16
Photo recording ··································································· 1-17
Interval recording ································································ 1-17
Cut recording ······································································ 1-19
Selecting automatic or manual mode ·································· 1-20
Focusing manually ······························································ 1-21
Adjusting the aperture ························································· 1-22
Adjusting the shutter speed ················································· 1-23
Adjusting the gain ······························································· 1-25
Tips for manual adjustment ················································ 1-26
Adjusting the white balance ················································ 1-27
Using the ND filter ····························································· 1-29
Using the zebra pattern ······················································· 1-29
Adjusting the recording sound ············································ 1-30
Releasing the STEADY SHOT function ···························· 1-31
Making a custom preset ······················································ 1-32
Re-recording a picture in the middle of a recorded tape ···· 1-33
Searching the recorded picture ··········································· 1-34
Displaying recording data ··················································· 1-35
Editing onto another tape ···················································· 1-35
Audio dubbing ···································································· 1-36
Changing the mode settings ················································ 1-13
Overlapping two pictures ···················································· 1-15
Using the wide mode function ············································ 1-16
Photo recording ··································································· 1-17
Interval recording ································································ 1-17
Cut recording ······································································ 1-19
Selecting automatic or manual mode ·································· 1-20
Focusing manually ······························································ 1-21
Adjusting the aperture ························································· 1-22
Adjusting the shutter speed ················································· 1-23
Adjusting the gain ······························································· 1-25
Tips for manual adjustment ················································ 1-26
Adjusting the white balance ················································ 1-27
Using the ND filter ····························································· 1-29
Using the zebra pattern ······················································· 1-29
Adjusting the recording sound ············································ 1-30
Releasing the STEADY SHOT function ···························· 1-31
Making a custom preset ······················································ 1-32
Re-recording a picture in the middle of a recorded tape ···· 1-33
Searching the recorded picture ··········································· 1-34
Displaying recording data ··················································· 1-35
Editing onto another tape ···················································· 1-35
Audio dubbing ···································································· 1-36
Additional information
Changing the lithium battery in the digital camcorder ······· 1-37
Resetting the date and time ················································· 1-38
Notes on video cassettes ····················································· 1-39
Tips for using the battery pack ··········································· 1-40
Maintenance information and precautions ·························· 1-42
Using your digital camcorder abroad ································· 1-44
Identifying the parts ···························································· 1-45
Warning indicators ······························································ 1-53
Resetting the date and time ················································· 1-38
Notes on video cassettes ····················································· 1-39
Tips for using the battery pack ··········································· 1-40
Maintenance information and precautions ·························· 1-42
Using your digital camcorder abroad ································· 1-44
Identifying the parts ···························································· 1-45
Warning indicators ······························································ 1-53
2.
DISASSEMBLY
2-1.
REMOVAL OF EVF BLOCK ······································ 2-1
2-2.
REMOVAL OF EVF CABINET ·································· 2-2
2-3.
REMOVAL OF CRT BLOCK ······································ 2-3
2-4.
REMOVAL OF VF-105 BOARD ································· 2-3
2-5.
REMOVAL OF EM-10 BOARD ·································· 2-4
2-6.
REMOVAL OF PAD TERMINAL (1) ························· 2-4
2-7.
REMOVAL OF PAD TERMINAL (2) ························· 2-5
2-8.
REMOVAL OF SJ-15, RT-21, BOARD AND
PAD TERMINAL (3) ··················································· 2-5
PAD TERMINAL (3) ··················································· 2-5
2-9.
REMOVAL OF LH-10 BOARD ·································· 2-6
2-10. REMOVAL OF PAD FRAME ····································· 2-6
2-11. REMOVAL OF CABINET (R) BLOCK ······················ 2-7
2-12. REMOVAL OF SW-286 AND ED-44 BOARDS ········· 2-7
2-11. REMOVAL OF CABINET (R) BLOCK ······················ 2-7
2-12. REMOVAL OF SW-286 AND ED-44 BOARDS ········· 2-7
2-13. REMOVAL OF
CONTROL PANEL ASSEMBLY (1) ·························· 2-8
2-14. REMOVAL OF
CONTROL PANEL ASSEMBLY (2) ·························· 2-8
2-15. REMOVAL OF AM-38 AND FK-68 BOARDS ·········· 2-9
2-16. REMOVAL OF MECHANISM BLOCK (1) ··············· 2-9
2-17. REMOVAL OF MECHANISM BLOCK (2) ··············· 2-10
2-18. REMOVAL OF VK-41P BOARD ································ 2-10
2-19. REMOVAL OF LENS BLOCK ··································· 2-11
2-20. REMOVAL OF LD-86, CD-160 AND
2-16. REMOVAL OF MECHANISM BLOCK (1) ··············· 2-9
2-17. REMOVAL OF MECHANISM BLOCK (2) ··············· 2-10
2-18. REMOVAL OF VK-41P BOARD ································ 2-10
2-19. REMOVAL OF LENS BLOCK ··································· 2-11
2-20. REMOVAL OF LD-86, CD-160 AND
SE-56 BOARDS ··························································· 2-11
2-21. REMOVAL OF ZOOM LENS ASSEMBLY ··············· 2-12
2-22. REMOVAL OF FS-78 BOARD ··································· 2-12
2-23. REMOVAL OF MA-280 AND GP-14 BOARDS ········ 2-13
2-24. REMOVAL OF AU-192 BOARD ································ 2-13
2-25. REMOVAL OF JC-15P BOARD ································· 2-14
2-26. REMOVAL OF RS-73 BOARD ··································· 2-14
2-27. REMOVAL OF MG-16, CB-54P AND
2-22. REMOVAL OF FS-78 BOARD ··································· 2-12
2-23. REMOVAL OF MA-280 AND GP-14 BOARDS ········ 2-13
2-24. REMOVAL OF AU-192 BOARD ································ 2-13
2-25. REMOVAL OF JC-15P BOARD ································· 2-14
2-26. REMOVAL OF RS-73 BOARD ··································· 2-14
2-27. REMOVAL OF MG-16, CB-54P AND
DD-75P BOARDS ························································ 2-15
2-28. REMOVAL OF EJ-27, LI-60, JK-149, DV-27 AND
DS-74 BOARDS ·························································· 2-15
2-29. REMOVAL OF GRIP ASSEMBLY ····························· 2-16
2-30. REMOVAL OF CONTROL (ZK4520)
2-30. REMOVAL OF CONTROL (ZK4520)
SWITCH BLOCK ························································ 2-16
2-31. INTERNAL VIEWS ····················································· 2-17
2-32. CIRCUIT BOARDS LOCATION ································ 2-19
2-32. CIRCUIT BOARDS LOCATION ································ 2-19
3.
BLOCK DIAGRAMS
3-1.
OVERALL BLOCK DIAGRAM (1) ··························· 3-1
3-2.
OVERALL BLOCK DIAGRAM (2) ··························· 3-3
3-3.
OVERALL BLOCK DAIGRAM (3) ··························· 3-5
3-4.
OVERALL BLOCK DIAGRAM (4) ··························· 3-7
3-5.
OVERALL BLOCK DIAGRAM (5) ··························· 3-9
3-6.
POWER BLOCK DIAGRAM (1) ································ 3-11
3-7.
POWER BLOCK DIAGRAM (2) ································ 3-13
3-8.
POWER BLOCK DIAGRAM (3) ································ 3-15
4.
PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS
SCHEMATIC DIAGRAMS
4-1.
FRAME SCHEMATIC DIAGRAM ····························· 4-1
4-2.
PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS ········································· 4-5
SCHEMATIC DIAGRAMS ········································· 4-5
· JC-15P (1/7)(VIDEO CORE 1)
SCHEMATIC DIAGRAM ··························· 4-5
· JC-15P (2/7)(VIDEO CORE 2)
SCHEMATIC DIAGRAM ··························· 4-9
· JC-15P (3/7)(VIDEO CORE 3)
SCHEMATIC DIAGRAM ··························· 4-11
· JC-15P (4/7)(MODE CONTROL)
SCHEMATIC DIAGRAM ··························· 4-13
· JC-15P (5/7)(AUDIO) SCHEMATIC DIAGRAM ···· 4-16
· JC-15P (6/7)(HI CONTROL)
· JC-15P (6/7)(HI CONTROL)
SCHEMATIC DIAGRAM ··························· 4-19
· JC-15P (7/7) (DV INPUT/OUTPUT),
DV-27 (DV TERMINAL)
SCHEMATIC DIAGRAM ··························· 4-22
· DV-27 (DV TERMINAL)
PRINTED WIRING BOARD ······················ 4-25
· JC-15P (MAIN) PRINTED WIRING BOARD ········· 4-27
· CD-160 (CCD IMAGER)
· CD-160 (CCD IMAGER)
PRINTED WIRING BOARD ······················ 4-32
· CD-160 (CCD IMAGER)
SCHEMATIC DIAGRAM ··························· 4-35
— 4 —
· SE-56 (STEADY SHOT SENSOR)
SCHEMATIC DIAGRAM ··························· 4-37
· SE-56 (STEADY SHOT SENSOR)
PRINTED WIRING BOARD ······················ 4-38
· LD-86 (LENS DRIVE)
PRINTED WIRING BOARD ······················ 4-40
· LD-86 (LENS DRIVE) SCHEMATIC DIAGRAM ·· 4-43
· MG-16 (MAGIC) SCHEMATIC DIAGRAM ··········· 4-46
· MG-16 (MAGIC) PRINTED WIRING BOARD ······ 4-49
· CB-54P (MAIN) PRINTED WIRING BOARD ········ 4-51
· CB-54P (1/3)(CAMERA) SCHEMATIC DIAGRAM 4-56
· CB-54P (2/3)(BASE BAND)
· MG-16 (MAGIC) SCHEMATIC DIAGRAM ··········· 4-46
· MG-16 (MAGIC) PRINTED WIRING BOARD ······ 4-49
· CB-54P (MAIN) PRINTED WIRING BOARD ········ 4-51
· CB-54P (1/3)(CAMERA) SCHEMATIC DIAGRAM 4-56
· CB-54P (2/3)(BASE BAND)
SCHEMATIC DIAGRAM ··························· 4-61
· CB-54P (3/3)(VIDEO OUTPUT)
SCHEMATIC DIAGRAM ··························· 4-64
· RS-73 (1/2)(MECHANIAM CONTROL)
SCHEMATIC DIAGRAM ··························· 4-67
· RS-73 (2/2)(SERVO CONTROL),
MD-70 (TAPE SENSOR)
SCHEMATIC DIAGRAMS ························· 4-71
· MD-70 (TAPE SENSOR)
PRINTED WIRING BOARD ······················ 4-75
· RS-73 (MECHANISM/SERVO CONTROL)
PRINTED WIRING BOARD ······················ 4-77
· FK-68 (CONTROL PANEL)
PRINTED WIRING BOARD ······················ 4-80
· FK-68 (CONTROL PANEL),
ED-44 (EDIT SEARCH SWITCH),
AM-38 (SHUTTER SPEED SWITCH),
SW-286 (POWER SWITCH)
AM-38 (SHUTTER SPEED SWITCH),
SW-286 (POWER SWITCH)
SCHEMATIC DIAGRAMS ························· 4-83
· ED-44 (EDIT SEARCH SWITCH),
AM-38 (SHUTTER SPEED SWITCH),
SW-286 (POWER SWITCH)
SW-286 (POWER SWITCH)
PRINTED WIRING BOARDS ···················· 4-86
· AU-192 (1/2)(AUDIO),
JK-149 (VIDEO/AUDIO OUTPUT TERMINAL),
EM-10 (MIC JACK), MA-280 (MIC AMP)
EM-10 (MIC JACK), MA-280 (MIC AMP)
SCHEMATIC DIAGRAMS ························· 4-89
· AU-192 (2/2)(AUDIO SELECT),
EJ-27 (EJECT SWITCH),
GP-14 (BUZZER), HR-11 (REMOTE SENSOR 2),
SJ-15 (AUDIO INPUT TERMINAL),
LH-10 (HEADPHONE JACK),
RT-21 (RENOTE SENSOR 1),
VK-41P (PLAYER SWITCH),
FS-78 (START/STOP SWITCH),
LI-60 (LITHIUM BATTERY),
VF-105 (EVF CONNECTOR)
SCHEMATIC DIAGRAMS ······································· 4-94
GP-14 (BUZZER), HR-11 (REMOTE SENSOR 2),
SJ-15 (AUDIO INPUT TERMINAL),
LH-10 (HEADPHONE JACK),
RT-21 (RENOTE SENSOR 1),
VK-41P (PLAYER SWITCH),
FS-78 (START/STOP SWITCH),
LI-60 (LITHIUM BATTERY),
VF-105 (EVF CONNECTOR)
SCHEMATIC DIAGRAMS ······································· 4-94
· VF-105 (EVF CONNECTOR),
LI-60 (LITHIUMBATTERY)
PRINTED WIRING BOARDS ·································· 4-99
PRINTED WIRING BOARDS ·································· 4-99
· AU-192 (AUDIO) PRINTED WIRING BOARD ······ 4-101
· JK-149 (VIDEO/AUDIO OUTPUT),
· JK-149 (VIDEO/AUDIO OUTPUT),
EM-10 (MIC JACK), MA-260 (MIC AMP)
PRINTED WIRING BOARDS ·································· 4-106
PRINTED WIRING BOARDS ·································· 4-106
· EJ-27 (EJECT SWITCH ), GP-14 (BUZZER),
HR-11 (REMOTE SENSOR 2),
SJ-15 (AUDIO INPUT TERMINAL),
LH-10 (HEADPHONE JACK),
RT-21 (REMOTE SENSOR 1),
VK-41P (PLAYER SWITCH),
FS-78 (START/STOP SWITCH)
PRINTED WIRING BOARDS ·································· 4-111
SJ-15 (AUDIO INPUT TERMINAL),
LH-10 (HEADPHONE JACK),
RT-21 (REMOTE SENSOR 1),
VK-41P (PLAYER SWITCH),
FS-78 (START/STOP SWITCH)
PRINTED WIRING BOARDS ·································· 4-111
· DD-75P (POWER), DS-74 (DC IN)
PRINTED WIRING BOARDS ·································· 4-115
· DD-75P (POWER), DS-74 (DC IN)
SCHEMATIC DIAGRAMS ······································· 4-119
5.
REPAIR PARTS LIST
5-1.
EXPLODED VIEWS ··················································· 5-1
5-1-1. OVERALL-1 SECTION ·············································· 5-1
5-1-2. OVERALL-2 SECTION ·············································· 5-2
5-1-3. CABINET (R) SECTION ············································ 5-3
5-1-4. EVF SECTION ····························································· 5-4
5-1-5. MAIN BOARD SECTION ··········································· 5-5
5-1-6. POWER BOARD SECTION ······································· 5-6
5-1-7. GRIP SECTION ··························································· 5-7
5-1-8. CABINET (L) SECTION ············································· 5-8
5-1-9. MAIN FRAME SECTION ··········································· 5-9
5-1-10. CCD BOARD SECTION ·········································· 5-10
5-1-11. ZOOM LENS SECTION ··········································· 5-11
5-1-12. CASSETTE COMPARTMENT
5-1-2. OVERALL-2 SECTION ·············································· 5-2
5-1-3. CABINET (R) SECTION ············································ 5-3
5-1-4. EVF SECTION ····························································· 5-4
5-1-5. MAIN BOARD SECTION ··········································· 5-5
5-1-6. POWER BOARD SECTION ······································· 5-6
5-1-7. GRIP SECTION ··························································· 5-7
5-1-8. CABINET (L) SECTION ············································· 5-8
5-1-9. MAIN FRAME SECTION ··········································· 5-9
5-1-10. CCD BOARD SECTION ·········································· 5-10
5-1-11. ZOOM LENS SECTION ··········································· 5-11
5-1-12. CASSETTE COMPARTMENT
BLOCK SECTION ···················································· 5-12
5-1-13. MECHANISM CHASSIS BLOCK (1) SECTION ··· 5-13
5-1-14. MECHANISM CHASSIS BLOCK (2) SECTION ··· 5-14
5-2.
5-1-14. MECHANISM CHASSIS BLOCK (2) SECTION ··· 5-14
5-2.
ELECTRICAL PARTS LIST ······································· 5-15
6.
ADJUSTMENTS
6-1.
CAMERA SECTION ADJUSTMENT ························ 6-1
1-1.
PREPARATIONS BEFORE ADJUSTMENT ·············· 6-1
1-1-1. List of service tools ······················································ 6-1
1-1-2. Preparations ·································································· 6-5
1-1-3. Precautions ··································································· 6-6
1.
1-1-2. Preparations ·································································· 6-5
1-1-3. Precautions ··································································· 6-6
1.
Switch settings ······························································ 6-6
2.
Adjustment sequence ···················································· 6-6
3.
Subject ·········································································· 6-6
1-1-4. Adjustment remote commander (RM-95 upgraded) ···· 6-7
1.
1.
Using the adjustment remote commander ···················· 6-7
2.
Precautions when using
the adjustment remote commander ······························· 6-8
the adjustment remote commander ······························· 6-8
1-1-5. Page F address list ························································ 6-9
1-1-6. Page E address list ························································ 6-12
1-2.
1-1-6. Page E address list ························································ 6-12
1-2.
CAMERA SYSTEM ADJUSTMENTS ······················· 6-13
1-2-1. Adjustment points when major parts
have been replaced ······················································· 6-13
1-2-2. Power supply voltage check (DD-75P board) ·············· 6-13
1-2-3. Initialization of Pages E and F data ······························ 6-14
1-2-4. Modification of Page F data ········································· 6-14
1-2-5. Modification of Page E data ········································· 6-14
1-2-6. 28MHz crystal oscillator adjustment
1-2-3. Initialization of Pages E and F data ······························ 6-14
1-2-4. Modification of Page F data ········································· 6-14
1-2-5. Modification of Page E data ········································· 6-14
1-2-6. 28MHz crystal oscillator adjustment
(CB-54P board) ···························································· 6-15
1-2-7. Zoom center value preset ·············································· 6-15
1-2-8. V SUB adjustment ························································ 6-16
1-2-9. VRG adjustment ··························································· 6-17
1-2-10. HALL adjustment ······················································ 6-18
1-2-11. Offset check and adjustment ······································ 6-20
1-2-12. Flange back adjustment and
1-2-8. V SUB adjustment ························································ 6-16
1-2-9. VRG adjustment ··························································· 6-17
1-2-10. HALL adjustment ······················································ 6-18
1-2-11. Offset check and adjustment ······································ 6-20
1-2-12. Flange back adjustment and
temperature data reading ··········································· 6-21
1-2-13. Flange back check ······················································ 6-22
1-2-14. Picture frame setting ·················································· 6-23
1-2-15. Auto white balance reference data input ···················· 6-24
1-2-16. IRIS IN/OUT adjustment ··········································· 6-25
1-2-17. MAX GAIN adjustment ············································· 6-26
1-2-18. White balance adjustment with
1-2-14. Picture frame setting ·················································· 6-23
1-2-15. Auto white balance reference data input ···················· 6-24
1-2-16. IRIS IN/OUT adjustment ··········································· 6-25
1-2-17. MAX GAIN adjustment ············································· 6-26
1-2-18. White balance adjustment with
ND filter correction ··················································· 6-27
1-2-19. Auto white balance adjustment ·································· 6-28
