DCR-TRV940, DCR-TRV940E, DCR-TRV950, DCR-TRV950E (serv.man2) - Sony Movie Service Manual (repair manual). Page 10

1-5

C

C

C

C

C

C

C

C

C

C

C

C

C

C

C

C

C

C

C

C

C

C

C

E

E

E

E

E

E

0

4

2

1

2

2

3

1

3

1

3

1

3

1

3

1

3

1

3

1

3

1

3

1

3

1

3

1

3

1

3

2

3

2

3

2

3

2

3

2

3

2

3

2

3

2

2

0

6

1

6

1

6

2

6

2

9

1

0

0

0

0

0

0

1

0

1

1

2

0

2

1

2

2

2

3

2

4

3

0

4

0

4

2

1

0

1

1

2

0

2

1

2

2

2

3

2

4

3

0

4

0

4

2

0

0

0

0

1

0

0

0

0

1

0

1

Non-standard battery is used.

Condensation.

Video head is dirty.

LOAD direction. Loading does not
complete within specified time

UNLOAD direction. Loading does not
complete within specified time

T reel side tape slacking when unloading.

Winding S reel fault when counting the
rest of tape.

T reel fault.

S reel fault.

T reel fault.

FG fault when starting capstan.

FG fault when starting drum.

FG fault during normal drum operations.

LOAD direction loading motor time-
out.

UNLOAD direction loading motor
time-out.

T reel side tape slacking when
unloading.

Winding S reel fault when counting the
rest of tape.

T reel fault.

S reel fault.

T reel fault.

FG fault when starting capstan.

FG fault when starting drum

FG fault during normal drum
operations

EEPROM data error

Difficult to adjust focus
(Cannot initialize focus.)

Zoom operations fault
(Cannot initialize zoom lens.)

Steadyshot function does not work well.
(With pitch angular velocity sensor output
stopped.)

Steadyshot function does not work well.
(With yaw angular velocity sensor output
stopped.)

Abnormality when flash is being charged.

Use the info LITHIUM battery.

Remove the cassette, and insert it again after one hour.

Clean with the optional cleaning cassette.

Load the tape again, and perform operations from the beginning.

Load the tape again, and perform operations from the beginning.

Load the tape again, and perform operations from the beginning.

Load the tape again, and perform operations from the beginning.

Load the tape again, and perform operations from the beginning.

Load the tape again, and perform operations from the beginning.

Load the tape again, and perform operations from the beginning.

Load the tape again, and perform operations from the beginning.

Load the tape again, and perform operations from the beginning.

Load the tape again, and perform operations from the beginning.

Remove the battery or power cable, connect, and perform
operations from the beginning.

Remove the battery or power cable, connect, and perform
operations from the beginning.

Remove the battery or power cable, connect, and perform
operations from the beginning.

Remove the battery or power cable, connect, and perform
operations from the beginning.

Remove the battery or power cable, connect, and perform
operations from the beginning.

Remove the battery or power cable, connect, and perform
operations from the beginning.

Remove the battery or power cable, connect, and perform
operations from the beginning.

Remove the battery or power cable, connect, and perform
operations from the beginning.

Remove the battery or power cable, connect, and perform
operations from the beginning.

Remove the battery or power cable, connect, and perform
operations from the beginning.

Initialize A, D page data (EEPROM data).

Inspect the lens block focus MR (Pin qf,  qg  of DB-014 board
CN1004) when focusing is performed when the focus ring is rotated
in the focus manual mode, and the focus motor drive circuit (IC3402
of DB-014 board) when the focusing is not performed.

Inspect the lens block zoom MR (Pin  0,  qs  of DB-014 board
CN1004) when zooming is performed when the zoom lens is
operated and the zoom motor drive circuit (IC3402 of DB-014
board) when zooming is not performed.

Inspect pitch angular velocity sensor (SE4001 of SE-132 board)
peripheral circuits.

Inspect yaw angular velocity sensor (SE4002 of SE-132 board)
peripheral circuits.

Checking of flash unit or replacement of flash unit. (Note)

After repair, be sure to perform “1-7. PROCESS AFTER FIXING FLASH ERROR”.