DCR-TRV16, DCR-TRV16E, DCR-TRV18, DCR-TRV18E (serv.man2) - Sony Movie Service Manual (repair manual). Page 113

5-39

Before performing the adjustments, check the data of page: 0,
address: 10 is “00”. If not, set data: 00 to this address.

1)

The adjustments of this unit are performed in the VTR mode
or camera mode.
To set to the VTR mode, set the power switch to “VCR” (or
“PLAYER”) or set the “Forced VTR Power ON mode” using
the adjusting remote commander (Note2).
To set to the Camera mode, set the power switch to “CAMERA”
or set the “Forced Camera Power ON mode” using the adjusting
remote commander (Note3).
After completing adjustments, be sure to exit the “Forced VTR
Power ON Mode” or “Forced Camera Power ON Mode”.
(Note5)

2)

The front panel block ( Focus ring, Microphone unit., MA-409
board,  FB-219 board) need not be assembled. To remove it,
disconnect the following connector.

VA-117 board CN4003 (24P, 0.5mm)

3)

Cabinet (R) (CK-108board, LCD block) need not be connected.
But removing the cabinet (R) (removing the VC-280 board
CN1005) means removing the lithium 3V power supply (CK-
108 board, BT5201) , data such as date, time, user-set menus
will be lost. After completing adjustments, reset these data.
But, the self-diagnosis data and the data on history of use (total
drum rotation time etc.) will be kept even if the cabinet (R) has
been removed. (Refer to “5-4.Service Mode” for the data on
the history use and the self-diagnosis data.)
To remove the cabinet (R), disconnect the following connectors.

VA-117 board CN4004 (12P, 0.5mm)
VC-280 board CN1005 (28P, 0.5mm)

4)

The EVF block (LB-077 board) is need not be connected. To
remove it, disconnect the following connector.

VA-117 board CN4201 (20P, 0.5mm)

5)

The intelligent accessory shoe is need not be connected. To
remove it, disconnect the following connector.

VA-117 board CN4001 (20P, 0.5mm)

6)

To open the VA-117 board, use the following extension cable
between the VA-117 board CN4002 and VC-280 board
CN1007.

J-6082-352-A (100P, 0.5mm)

7)

The lens block (CD-365 board) is need not be connected. To
remove it, disconnect the following connectors.

VC-280 board CN1401 (16P, 0.5mm)
VC-280 board CN1201 (24P, 0.5mm)

8)

By setting the “Forced VTR Power ON mode”, the video section
can be operate even if the control switch block (PS-CX2670)
has been removed. When removing it, disconnect the following
connector.

VC-280 board CN1008 (20P, 0.5mm)

Setting the “Forced VTR Power ON” mode (VTR mode)
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 02, and press the PAUSE

button of the adjusting remote commander.
The above procedure will enable the VTR power to be turned
on with the control switch block (PS-CX2670 block) removed.
After completing adjustments, be sure to exit the “Forced Power
ON mode”.

Setting the “Forced Camera Power ON” mode (Camera mode)
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 01, and press the PAUSE

button of the adjusting remote commander.
The above procedure will enable the camera power to be turned
on with the control switch block (PS-CX2670 block) removed.
After completing adjustments, be sure to exit the “Forced Power
ON mode”.

Setting the “Forced Memory Power ON” mode (Memory mode)
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 05, and press the PAUSE

button of the adjusting remote commander.
The above procedure will enable the memory power to be
turned on with the control switch block (PS-CX2670 block)
removed.
After completing adjustments, be sure to exit the “Forced Power
ON mode”.

Exiting the “Forced Power ON” mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 00, and press the PAUSE

button of the adjusting remote commander.

3) Select page: 0, address: 01, and set data: 00.