Read Sony DCR-SX33E / DCR-SX34E / DCR-SX43 / DCR-SX43E / DCR-SX44 / DCR-SX44E / DCR-SX53E / DCR-SX63 / DCR-SX63E (serv.man2) Service Manual online
DCR-SX33E/SX34E/SX43/SX43E/SX44/SX44E/SX53E/SX63/SX63E_L2
1-2E
1-4-3. Self-diagnosis Code Table
Self-diagnosis Code
Symptom/State
Correction
Repaired by:
Block
Function
Detailed
Code
C
0
4
0
0
Non-standard battery is used.
Use the InfoLITHIUM battery.
C
0
6
0
0
The battery pack temperature is high.
Change the battery pack or replace it in a cool place.
C
1
3
0
1
Memory card is unformatted.
Memory card is broken.
Memory card is broken.
Format the memory card.
Insert a new memory card.
Insert a new memory card.
C
1
3
0
2
Access error
(SX34/SX44/SX44E/SX53/SX63/
SX63E)
(SX34/SX44/SX44E/SX53/SX63/
SX63E)
Remove the power source. Reconnect it again and operate
your camcorder again.
your camcorder again.
E
2
0
0
0
Flash memory data are rewritten.
Make flash memory data correct value.
(Note 1)
E
6
1
0
0
Difficult to adjust focus
(Cannot initialize focus.)
(Cannot initialize focus.)
Inspect the lens block focus reset sensor (pin
8 of CN5401
on the VC-587 board) when focusing is performed when the
focus buttons of the touch panel are pressed in the focus manual
mode, and the focus motor driver circuit (IC5401 on the VC-587
board) when focusing is not performed.
focus buttons of the touch panel are pressed in the focus manual
mode, and the focus motor driver circuit (IC5401 on the VC-587
board) when focusing is not performed.
E
6
1
1
0
Zoom operations fault
(Cannot initialize zoom lens.)
(Cannot initialize zoom lens.)
Inspect the lens block zoom MR sensor (pin
0 of CN5401 on
the VC-587 board) when zooming is performed when the zoom
lever is operated, or the zoom motor drive circuit (IC5401 on
the VC-587 board) when zooming is not performed.
lever is operated, or the zoom motor drive circuit (IC5401 on
the VC-587 board) when zooming is not performed.
E
6
1
1
1
The abnormalities in initialization of
the focus lens and the abnormalities in
initialization of the zoom lens occurred
simultaneously.
the focus lens and the abnormalities in
initialization of the zoom lens occurred
simultaneously.
Check E: 61: 00 and E: 61: 10 of the self-diagnosis code.
E
9
2
0
1
Battery current value gose over the
max discharge current
max discharge current
Check the remaining battery power because this symptom
may be depended on the remaining battery level, and comfirm
whether or not the symptom is occurred after replacing the
battery. If the symptom is still occurred, overhaul inspection
is needed. Check each output of DC/DC converter (IC4701)
on VC-587 board connected to DA-049 board with extension
cable (100P), and connect DC/Batt harness (the minimum
connection to periphery) to DA-049 board.
may be depended on the remaining battery level, and comfirm
whether or not the symptom is occurred after replacing the
battery. If the symptom is still occurred, overhaul inspection
is needed. Check each output of DC/DC converter (IC4701)
on VC-587 board connected to DA-049 board with extension
cable (100P), and connect DC/Batt harness (the minimum
connection to periphery) to DA-049 board.
E
9
4
0
0
Fault of writing or erasing the flash
memory
memory
Inspect the flash memory (IC7301 on the MS-428 board).
E
9
4
0
1
Internal memory fault
Format the internal memory (IC7301 on the MS-428 board).
Inspect or replacement of the internal memory (IC7301 on the
MS-428 board). (Note 2)
Inspect or replacement of the internal memory (IC7301 on the
MS-428 board). (Note 2)
Note1: Start the Adjust Manual in the Adjust Station and refer to the “Destination data write”.
Note2: Start the Adjust Manual in the Adjust Station and refer to the “INTERNAL MEMORY ADJUSTMENTS”.
Note2: Start the Adjust Manual in the Adjust Station and refer to the “INTERNAL MEMORY ADJUSTMENTS”.
The changed portions from
Ver. 1.0 are shown in blue.
Ver. 1.0 are shown in blue.
Ver. 1.1 2010.02
Click on the first or last page to see other DCR-SX33E / DCR-SX34E / DCR-SX43 / DCR-SX43E / DCR-SX44 / DCR-SX44E / DCR-SX53E / DCR-SX63 / DCR-SX63E (serv.man2) service manuals if exist.