Read Sony DCR-SR77E / DCR-SR87 / DCR-SR87E (serv.man2) Service Manual online
1-3
ENGLISH
JAPANESE
ENGLISH
JAPANESE
DCR-SR77E/SR87/SR87E_L2
1-4-3. Self-diagnosis Code Table
C
C
C
E
E
E
E
E
E
E
E
Block
Function
0
4
1
3
1
3
2
0
3
1
6
1
6
1
6
1
6
2
6
2
9
4
Detailed
Code
0
0
0
1
0
2
0
0
0
0
0
0
1
0
1
1
0
0
0
1
0
0
Symptom/State
Non-standard battery is used.
“Memory Stick Duo” is unformatted.
“Memory Stick Duo” is broken.
“Memory Stick Duo” is broken.
Disc access error
Flash memory data are rewritten.
Drive fault
Difficult to adjust focus
(Cannot initialize focus.)
(Cannot initialize focus.)
Zoom operations fault
(Cannot initialize zoom lens.)
(Cannot initialize zoom lens.)
The abnormalities in initialization of
the focus lens and the abnormalities in
initialization of the zoom lens occurred
simultaneously.
the focus lens and the abnormalities in
initialization of the zoom lens occurred
simultaneously.
Handshake correction function does not
work well. (With PITCH angular
velocity sensor output stopped.)
work well. (With PITCH angular
velocity sensor output stopped.)
Handshake correction function does not
work well. (With YAW angular velocity
sensor output stopped.)
work well. (With YAW angular velocity
sensor output stopped.)
Fault of writing to or erasing the flash
memory
memory
Self-diagnosis Code
Repaired b
y:
Correction
Use the InfoLITHIUM battery.
Format the “Memory Stick Duo”.
Insert a new “Memory Stick Duo”.
Insert a new “Memory Stick Duo”.
Remove the power source. Reconnect it again and operate your
camcorder again
camcorder again
Make flash memory data correct value. (Note 1)
Inspect or replacement of the hard disc drive.
Inspect the lens block focus reset sensor (pin 7 of CN5101 on
the VC-554 board) when focusing is performed when the focus
buttons of the touch panel are pressed in the focus manual mode,
and the focus motor drive circuit (IC5301 on the VC-554 board)
when the focusing is not performed.
the VC-554 board) when focusing is performed when the focus
buttons of the touch panel are pressed in the focus manual mode,
and the focus motor drive circuit (IC5301 on the VC-554 board)
when the focusing is not performed.
Inspect the lens block zoom reset sensor (pin qa of CN5101 on
the VC-554 board) when zooming is performed when the zoom
lever is operated, and the zoom motor drive circuit (IC5301 on
the VC-554 board) when zooming is not performed.
the VC-554 board) when zooming is performed when the zoom
lever is operated, and the zoom motor drive circuit (IC5301 on
the VC-554 board) when zooming is not performed.
Check whether the flexible board of the lens is broken, and
check whether it is inserted imperfectly. If there is no problem in
the flexible board, inspect the focus/zoom motor drive circuit
(IC5301 on the VC-554 board).
check whether it is inserted imperfectly. If there is no problem in
the flexible board, inspect the focus/zoom motor drive circuit
(IC5301 on the VC-554 board).
Inspect PITCH angular velocity sensors (SE7002 on the CD-
672/CD-687 board) peripheral circuits.
672/CD-687 board) peripheral circuits.
Inspect YAW angular velocity sensors (SE7001 on the CD-672/
CD-687 board) peripheral circuits.
CD-687 board) peripheral circuits.
Inspect the flash memory (IC7801 on the VC-554 board). (Note 1)
Note 1:
Start the Adjust Manual in the Adjust Station and refer to the “DESTINATON DATA WRITE”.
Click on the first or last page to see other DCR-SR77E / DCR-SR87 / DCR-SR87E (serv.man2) service manuals if exist.