Read Sony DCR-SR32E / DCR-SR33E / DCR-SR42 / DCR-SR42A / DCR-SR42E / DCR-SR52E / DCR-SR62 / DCR-SR62E / DCR-SR72E / DCR-SR82 / DCR-SR82C / DCR-SR82E (serv.man2) Service Manual online
1-2
DCR-SR32E/SR33E/SR42/SR42A/SR42E/SR52E/SR62/SR62E/SR72E/SR82/SR82C/SR82E_L2
ENGLISH
JAPANESE
ENGLISH
JAPANESE
1-2-3. Self-diagnosis Code Table
C
C
C
C
E
E
E
E
E
E
E
Block
Function
0
4
1
3
1
3
3
2
2
0
3
1
6
1
6
1
6
2
6
2
9
4
Detailed
Code
0
0
0
1
0
2
6
0
0
0
0
0
1
0
1
1
0
0
0
1
0
0
Symptom/State
Non-standard battery is used.
“Memory Stick Duo” is unformatted.
“Memory Stick Duo” is broken.
“Memory Stick Duo” is broken.
Disc access error
Difficult to adjust focus
(Cannot initialize focus)
(Cannot initialize focus)
EEPROM data are rewritten.
Drive fault
Zoom operations fault
(Cannot initialize zoom lens.)
(Cannot initialize zoom lens.)
The abnormalities in initialization of
the focus lens and the abnormalities in
initialization of the zoom lens occurred
simultaneously.
the focus lens and the abnormalities in
initialization of the zoom lens occurred
simultaneously.
Handshake correction function does not
work well. (With PITCH angular
velocity sensor output stopped.)
work well. (With PITCH angular
velocity sensor output stopped.)
Handshake correction function does not
work well. (With YAW angular velocity
sensor output stopped.)
work well. (With YAW angular velocity
sensor output stopped.)
Fault of writing to or erasing the
flashmemory
flashmemory
Self-diagnosis Code
Repaired b
y:
Correction
Use the InfoLITHIUM battery.
Format the “Memory Stick Duo”.
Insert a new “Memory Stick Duo”.
Insert a new “Memory Stick Duo”.
Remove the power source. Reconnect it again and operate your
camcorder again
camcorder again
Retry turn the power on by the power switch. If it does not
recover, check the focus MR sensor of lens block (pin 7 of
CN5301 on the VC-489 board). If it is OK, check the focus
motor drive IC (IC5601 on the VC-489 board: SR32E/SR33E/
SR42/SR42A/SR42E, IC5502 on the VC-489 board: SR52E/
SR62/SR62E/SR72E/SR82/SR82C/SR82E).
recover, check the focus MR sensor of lens block (pin 7 of
CN5301 on the VC-489 board). If it is OK, check the focus
motor drive IC (IC5601 on the VC-489 board: SR32E/SR33E/
SR42/SR42A/SR42E, IC5502 on the VC-489 board: SR52E/
SR62/SR62E/SR72E/SR82/SR82C/SR82E).
Make EEPROM data correct value.
Inspect or replacement of the hard disk drive.
Inspect the lens block zoom MR sensor (pin qa of CN5301 on
the VC-489 board) when zooming is performed when the zoom
lever is operated, and the zoom motor drive circuit (IC5601 on
the VC-489 board: SR32E/SR33E/SR42/SR42A/SR42E, IC5502
on the VC-489 board: SR52E/SR62/SR62E/SR72E/SR82/
SR82C/SR82E) when zooming is not performed.
the VC-489 board) when zooming is performed when the zoom
lever is operated, and the zoom motor drive circuit (IC5601 on
the VC-489 board: SR32E/SR33E/SR42/SR42A/SR42E, IC5502
on the VC-489 board: SR52E/SR62/SR62E/SR72E/SR82/
SR82C/SR82E) when zooming is not performed.
Check both C: 32: 60 and E: 61: 10 of the self-diagnosis code.
Inspect PITCH angular velocity sensors (SE7002 on the CD-672
board) peripheral circuits.(SR52E/SR62/SR62E/SR72E/SR82/
SR82C/SR82E)
board) peripheral circuits.(SR52E/SR62/SR62E/SR72E/SR82/
SR82C/SR82E)
Inspect YAW angular velocity sensors (SE7001 on the CD-672
board) peripheral circuits.(SR52E/SR62/SR62E/SR72E/SR82/
SR82C/SR82E)
board) peripheral circuits.(SR52E/SR62/SR62E/SR72E/SR82/
SR82C/SR82E)
Inspect the flash memory (IC2201 on the VC-489 board).
Click on the first or last page to see other DCR-SR32E / DCR-SR33E / DCR-SR42 / DCR-SR42A / DCR-SR42E / DCR-SR52E / DCR-SR62 / DCR-SR62E / DCR-SR72E / DCR-SR82 / DCR-SR82C / DCR-SR82E (serv.man2) service manuals if exist.