Read Sony DCR-SR30E / DCR-SR40 / DCR-SR40E (serv.man2) Service Manual online
1-3
DCR-SR30E/SR40/SR40E_L2
1-3-3. Self-diagnosis Code Table
C
C
C
C
E
E
E
E
E
E
E
E
E
E
E
Block
Function
0
4
1
3
1
3
3
2
2
0
3
1
4
0
4
0
6
1
6
1
6
1
6
2
6
2
9
4
9
4
Detailed
Code
0
0
0
0
0
2
5
0
0
0
0
0
0
0
0
1
0
0
1
0
1
1
0
0
0
1
0
0
0
1
-
Symptom/State
Non-standard battery is used.
Disk is faulty.
Disk access error
Codec IC dose not return any reply
EEPROM data are rewritten.
Drive fault
Codec IC fault
Audio Codec IC fault
Difficult to adjust focus
(Cannot initialize focus.)
(Cannot initialize focus.)
Zoom operations fault
(Cannot initialize zoom lens.)
(Cannot initialize zoom lens.)
The abnormalities in initialization of
the focus lens and the abnormalities in
initialization of the zoom lens occurred
simultaneously.
the focus lens and the abnormalities in
initialization of the zoom lens occurred
simultaneously.
Handshake correction function does not
work well. (With PITCH angular
velocity sensor output stopped.)
work well. (With PITCH angular
velocity sensor output stopped.)
Handshake correction function does not
work well. (With YAW angular velocity
sensor output stopped.)
work well. (With YAW angular velocity
sensor output stopped.)
Fault of writing to or erasing the
flashmemory
flashmemory
Fault of writing to or erasing EEPROM
Self-diagnosis Code
Repaired b
y:
Correction
Use the InfoLITHIUM battery.
Remove the power source. Reconnect it again and operate your
camcorder again
camcorder again
Remove the power source. Reconnect it again and operate your
camcorder again
camcorder again
Remove the power source. Reconnect it again and operate your
camcorder again
camcorder again
Make EEPROM data correct value. (Note 1)
Inspect or replacement of the hard disk drive
Inspect or replacement of the codec IC (IC2301on the VC-466
board) peripheral circuits
board) peripheral circuits
Inspect or replacement of the Audio Codec IC (IC2301 on the
VC-466 board) peripheral circuits
VC-466 board) peripheral circuits
Inspect the lens block focus reset sensor (pin ql of CN1301 on
the VC-466 board) when focusing is performed when the focus
buttons of the touch panel are pressed in the focus manual mode,
and the focus motor drive circuit (IC1301 on the VC-466 board)
when the focusing is not performed.
the VC-466 board) when focusing is performed when the focus
buttons of the touch panel are pressed in the focus manual mode,
and the focus motor drive circuit (IC1301 on the VC-466 board)
when the focusing is not performed.
Inspect the lens block zoom reset sensor (pin qg of CN1301 on
the VC-466 board) when zooming is performed when the zoom
lever is operated, and the zoom motor drive circuit (IC1301 on
the VC-466 board) when zooming is not performed.
the VC-466 board) when zooming is performed when the zoom
lever is operated, and the zoom motor drive circuit (IC1301 on
the VC-466 board) when zooming is not performed.
Check whether the flexible board of the lens is broken, and
check whether it is inserted imperfectly. If there is no problem in
the flexible board, inspect the focus/zoom motor drive circuit
(IC1301 on the VC-466 board).
check whether it is inserted imperfectly. If there is no problem in
the flexible board, inspect the focus/zoom motor drive circuit
(IC1301 on the VC-466 board).
Inspect PITCH angular velocity sensors (SE6101 on the CD-658
board) peripheral circuits.
board) peripheral circuits.
Inspect YAW angular velocity sensors (SE6102 on the CD-658
board) peripheral circuits.
board) peripheral circuits.
Inspect the flash memory (IC2401 on the VC-466 board). (Note 1)
Inspect the EEPROM (IC2303 on the VC-466 board). (Note 1)
Note 1:
Refer to “ 11-2. Record of Self-diagnosis Check” of “2-5. SERVICE MODE”, ADJ 9-852-139-51).
Click on the first or last page to see other DCR-SR30E / DCR-SR40 / DCR-SR40E (serv.man2) service manuals if exist.