Read Sony DCR-PC8E Service Manual online
— 2 —
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
0
OR DOTTED LINE WITH
MARK
0
ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
1.
Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.
connections. Check the entire board surface for solder splashes
and bridges.
2.
Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
"pinched" or contact high-wattage resistors.
3.
Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
4.
Look for parts which, through functioning, show obvious signs
of deterioration. Point them out to the customer and
recommend their replacement.
of deterioration. Point them out to the customer and
recommend their replacement.
5.
Check the B+ voltage to see it is at the values specified.
6.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
DCR-PC8E
TABLE OF CONTENTS
4.
PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS
SCHEMATIC DIAGRAMS
4-2.
SCHEMATIC DIAGRAMS ·········································· 4-19
• VC-265D (A/D CONVERTER)(1/16)
SCHEMATIC DIAGRAM ···························· 4-19
• VC-265D (CAMERA SIGNAL PROCESS)(2/16)
SCHEMATIC DIAGRAM ···························· 4-21
• VC-265D (LENS DRIVER)(3/16)
SCHEMATIC DIAGRAM ···························· 4-23
• VC-265D (DV SIGNAL PROCESS)(4/16)
SCHEMATIC DIAGRAM ···························· 4-25
• VC-265D (DV INTERFACE)(5/16)
SCHEMATIC DIAGRAM ···························· 4-27
• VC-265D (HI CONTROL)(6/16)
SCHEMATIC DIAGRAM ···························· 4-29
• VC-265D (LINE IN/OUT)(7/16)
SCHEMATIC DIAGRAM ···························· 4-31
• VC-265D (LINE A/D)(8/16)
SCHEMATIC DIAGRAM ···························· 4-33
• VC-265D (REC/PB AMP)(9/16)
SCHEMATIC DIAGRAM ···························· 4-35
• VC-265D (MECHA CONTROL)(10/16)
SCHEMATIC DIAGRAM ···························· 4-37
• VC-265D (DRUM/CAPSTAN MOTOR)(11/16)
SCHEMATIC DIAGRAM ···························· 4-39
• VC-265D (AUDIO IN/OUT)(12/16)
SCHEMATIC DIAGRAM ···························· 4-41
• VC-265D (EVF RGB DRIVER)(13/16)
SCHEMATIC DIAGRAM ···························· 4-43
• VC-265D (DC/DC CONVERTER)(14/16)
SCHEMATIC DIAGRAM ···························· 4-45
• VC-265D (DC/DC CONVERTER)(15/16)
SCHEMATIC DIAGRAM ···························· 4-47
• VC-265D (CONNECTOR)(16/16)
SCHEMATIC DIAGRAM ···························· 4-49
4-3.
PRINTED WIRING BOARDS
• VC-265D (A/D CONVERTER, CAMERA SIGNAL
PROCESS, LENS DRIVE, MS INTERFACE, DV
SIGNAL PROCESS, HI CONTROL, LINE IN/OUT,
REC/PB AMP, MECHA CONTROL, SERVO, AUDIO,
DC/DC CONVERTER)
SIGNAL PROCESS, HI CONTROL, LINE IN/OUT,
REC/PB AMP, MECHA CONTROL, SERVO, AUDIO,
DC/DC CONVERTER)
PRINTED WIRING BOARD ······················· 4-65
4-4.
WAVEFORMS ······························································ 4-71
4-5.
MOUNTED PARTS LOCATION ································· 4-75
6.
REPAIR PARTS LIST
6-2.
ELECTRICAL PARTS LIST ········································ 6-12
Click on the first or last page to see other DCR-PC8E service manuals if exist.