Read Sony DCR-PC109 / DCR-PC109E (serv.man4) Service Manual online
6-55
DCR-PC109/PC109E
4-3.
SERVICE MODE
Note: Before performing the adjustments, check the data of page: 0,
address: 10 is “00”. If not, set data: 00 to this address.
1. Setting the Test Mode
Page A
Address 10
• Before setting the data , select page: 0, address: 01, and set data: 01.
• For page A, the data set is recorded in the non-volatile memory
• For page A, the data set is recorded in the non-volatile memory
by pressing the PAUSE button of the adjustment remote
commander. In this case, take note that the test mode will not be
exited even when the main power is turned off.
commander. In this case, take note that the test mode will not be
exited even when the main power is turned off.
• After completing adjustments/repairs, be sure to return the data
of this address to 00, and press the PAUSE button of the adjustment
remote commander.
Select page: 0, address: 01, and set data: 00.
remote commander.
Select page: 0, address: 01, and set data: 00.
2. Emergence Memory Address (Camera section)
Page 19
Address 87 to 8A
Note: When reading or writing the 19 page data, select page: 0, address:
10, and set data: 01, then select 9 page. The 19 page can be chosen
by this data setting.
After reading or writing, reset the data of page: 0, address: 10 to “00”.
by this data setting.
After reading or writing, reset the data of page: 0, address: 10 to “00”.
3. Emergence Memory Address (Mechanism section)
Page C
Address F4 to FF
When no error occurs in this unit, data “00” is written in the above
addresses (F4 to FF). when first error occurs in the unit, the data
corresponding to the error is written in the first emergency address
(F4 to F7). In the same way, when the second error occurs, the data
corresponding to the error is written in the second emergency address
(F8 to FB). Finally, when the last error occurs, the data corresponding
to the error is written in the last emergency address (FC to FF).
addresses (F4 to FF). when first error occurs in the unit, the data
corresponding to the error is written in the first emergency address
(F4 to F7). In the same way, when the second error occurs, the data
corresponding to the error is written in the second emergency address
(F8 to FB). Finally, when the last error occurs, the data corresponding
to the error is written in the last emergency address (FC to FF).
Note: After completing adjustments, be sure to initialize the data of
addresses F4 to FF to “00”.
Initializing method:
1)
1)
Select page: 0, address: 01, and set data: 01.
2)
Select page: 3, address: 01, set data: 37, and press the PAUSE
button.
button.
3)
Check that the data of page:3, address:02 is “00”.
4)
Select page: 0, address: 01, and set data: 00.
3-1. EMG Code (Emergency Code)
Codes corresponding to the errors which occur are written in
addresses F4, F8 and FC. The type of error indicated by the code
are shown in the following table.
Codes corresponding to the errors which occur are written in
addresses F4, F8 and FC. The type of error indicated by the code
are shown in the following table.
Emergency Type
No error
Loading motor emergency during loading
Loading motor emergency during unloading
T reel emergency during normal rotation
S reel emergency during normal rotation
T reel emergency (Short circuit between S reel
terminal and T reel terminal)
terminal and T reel terminal)
FG emergency at the start up of the capstan
FG emergency at the start up of the drum
FG emergency during normal rotation of the drum
Code
00
10
11
22
23
24
30
40
42
Function
Normal
Forced camera power ON (CAMERA-TAPE mode)
Forced VTR power ON (PLAY/EDIT mode)
Forced camera + VTR power ON
Forced memory power ON (CAMERA-MEMORY mode)
Data
00
01
02
03
05
2-1. EMG Code (Emergency Code)
Codes corresponding to the errors which occur are written in 19
page, addresses 87 to 8A. The type of error indicated by the code
are shown in the following table.
Codes corresponding to the errors which occur are written in 19
page, addresses 87 to 8A. The type of error indicated by the code
are shown in the following table.
Note: After completing adjustments, be sure to initialize the data of
addresses 87 to 8A to “00”.
Initializing method:
1)
1)
Select page: 0, address: 01, and set data: 01.
2)
Select page: 0, address: 10, and set data: 00.
3)
Select page: 6, address: 01, set data: FD and press the PAUSE
button.
button.
4)
Check that the data of page: 6, address: 02 is “01”.
5)
Select page: 6, address: 01, set data: 00 and press the PAUSE
button.
button.
6)
Select page: 0, address: 01, and set data: 00.
Contents
EMG code when first error occurs
EMG code when second error occurs
EMG code when third error occurs
EMG code when last error occurs
Address
87
88
89
8A
Emergency Type
No error
Code
00
Contents
EMG code when first error occurs
Upper: MSW code when shift starts when first
error occurs
Lower: MSW code when first error occurs
error occurs
Lower: MSW code when first error occurs
Lower: MSW code to be moved when first error
occurs
occurs
EMG code when second error occurs
Upper: MSW code when shift starts when second
error occurs
Lower: MSW code when second error occurs
error occurs
Lower: MSW code when second error occurs
Lower: MSW code to be moved when second error
occurs
occurs
EMG code when last error occurs
Upper: MSW code when shift starts when last error
occurs
Lower: MSW code when last error occurs
occurs
Lower: MSW code when last error occurs
Lower: MSW code to be moved when last error
occurs
occurs
Address
F4
F6
F7
F8
FA
FB
FC
FE
FF
Click on the first or last page to see other DCR-PC109 / DCR-PC109E (serv.man4) service manuals if exist.