Read Sony DCR-PC103E / DCR-PC104E / DCR-PC105 / DCR-PC105E Service Manual online
SERVICE MANUAL
DIGITAL VIDEO CAMERA RECORDER
LEVEL
3
Revision History
Revision History
Ver 1.0 2003. 04
Z MECHANISM
• For INSTRUCTION MANUAL, refer to SERVICE MANUAL, LEVEL 1 (987625841.pdf).
• Reference No. search on printed wiring boards is available.
The information that is not described in this Service Manual is described
in the LEVEL 2 Service Manual.
When repairing, use this manual together with LEVEL 2 Service Manual.
in the LEVEL 2 Service Manual.
When repairing, use this manual together with LEVEL 2 Service Manual.
Contents of LEVEL 2 Service Manual
1. SERVICE NOTE
2. DISASSEMBLY
3. BLOCK DIAGRAMS
4. PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS
5. REPAIR PARTS LIST
6. ADJUSTMENTS
OVERALL
POWER
CD-444, PD-193, LI-070, BJ-004,
ST-084, FL4000, VF-156, NS-018,
CONTROL SWITCH BLOCK
(FK4400, PS4400),
FP-467, FP-468, FP-228, FP-672,
FP-697 FLEXIBLE
ST-084, FL4000, VF-156, NS-018,
CONTROL SWITCH BLOCK
(FK4400, PS4400),
FP-467, FP-468, FP-228, FP-672,
FP-697 FLEXIBLE
EXPLODED VIEWS
ELECTRICAL PARTS LIST
Link
PRINTED WIRING BOARDS
REPAIR PARTS LIST
SCHEMATIC DIAGRAMS
PRINTED WIRING BOARDS
REPAIR PARTS LIST
SCHEMATIC DIAGRAMS
Link
DCR-PC103E/PC104E/
PC105/PC105E
RMT-830/RMT-831
US Model
Canadian Model
Korea Model
DCR-PC105
AEP Model
UK Model
East European Model
DCR-PC103E/PC105E
E Model
Hong Kong Model
DCR-PC104E/PC105/PC105E
Chinese Model
DCR-PC104E/PC105E
Australian Model
DCR-PC105E
Tourist Model
DCR-PC105/PC105E
Photo : DCR-PC103E
— 2 —
DCR-PC103E/PC104E/PC105/PC105E
1.
Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.
connections. Check the entire board surface for solder splashes
and bridges.
2.
Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
"pinched" or contact high-wattage resistors.
3.
Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
4.
Look for parts which, through functioning, show obvious signs
of deterioration. Point them out to the customer and
recommend their replacement.
of deterioration. Point them out to the customer and
recommend their replacement.
5.
Check the B+ voltage to see it is at the values specified.
6.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
Unleaded solder
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40
• Unleaded solder melts at a temperature about 40
°
C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
°
C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
0
OR DOTTED LINE WITH
MARK
0
ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE
0
SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
CAUTION :
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
COVER
COVER
— 3 —
DCR-PC103E/PC104E/PC105/PC105E
TABLE OF CONTENTS
4.
PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS
SCHEMATIC DIAGRAMS
4-2.
SCHEMATIC DIAGRAMS
• VC-319 (1/18)(TIMING GENERATOR, S/H, AGC, A/D)
SCHEMATIC DIAGRAM ···························· 4-25
• VC-319 (2/18) (CAMERA PROCESS)
SCHEMATIC DIAGRAM ···························· 4-27
• VC-319 (3/18) (LENS DRIVE)
SCHEMATIC DIAGRAM ···························· 4-29
• VC-319 (4/18)(MPEG MOVIE/DV SIGNAL/AUDIO/
DIGITAL STILL CONTROL)
SCHEMATIC DIAGRAM ···························· 4-31
• VC-319 (5/18)(DIGITAL STILL CONTROL,
HI CONTROL)
HI CONTROL)
SCHEMATIC DIAGRAM ···························· 4-33
• VC-319 (6/18) (SDRAM/FLASH MEMORY)
SCHEMATIC DIAGRAM ···························· 4-35
• VC-319 (7/18)(DV SIGNAL PROCESSOR, RF SIGNAL
PROCESSOR)
SCHEMATIC DIAGRAM ···························· 4-37
• VC-319 (8/18) (DV INTERFACE)
SCHEMATIC DIAGRAM ···························· 4-39
• VC-319 (9/18) (REC/PB AMP)
SCHEMATIC DIAGRAM ···························· 4-41
• VC-319 (10/18) (VIDEO IN/OUT, AGC)
SCHEMATIC DIAGRAM ···························· 4-43
• VC-319 (11/18)(CAPSTAN/DRUM/LD MOTOR
DRIVE)
SCHEMATIC DIAGRAM ···························· 4-45
• VC-319 (12/18) (HI CONTROL)
SCHEMATIC DIAGRAM ···························· 4-47
• VC-319 (13/18)(MECHA CONTROL, CAMERA
CONTROL)
SCHEMATIC DIAGRAM ···························· 4-49
• VC-319 (14/18)(EVF RGB DRIVER,TIMING
GENERATOR)
GENERATOR)
SCHEMATIC DIAGRAM ···························· 4-51
• VC-319 (15/18)(AUDIO I/O, A/D, D/A CONVERTER)
SCHEMATIC DIAGRAM ···························· 4-53
• VC-319 (16/18) (CHARGE SWITCH)
SCHEMATIC DIAGRAM ···························· 4-55
• VC-319 (17/18)(DC/DC CONVERTER, REGURATOR)
SCHEMATIC DIAGRAM ···························· 4-57
• VC-319 (18/18) (CONNECTOR)
SCHEMATIC DIAGRAM ···························· 4-59
4-3.
PRINTED WIRING BOARDS
• VC-319 (TIMING GENERATOR, S/H, AGC, A/D,
CAMERA PROCESS, LENS DRIVE, MPEG MOVIE/
DV STILL/AUDIO DIGITAL STILL CONTROL,
DIGITAL STILL CONTROL, HI CONTROL, SDRAM/
FLASH MEMORY, DV SIGNAL PROCESSOR, RF
SIGNAL PROCESSOR, DV INTERFACE, REC/PB
AMP, VIDEO IN/OUT, AGC, CAPSTAN/DRUM/LD
MOTOR DRIVE, HI CONTROL, MECHA CONTROL,
CAMERA CONTROL, EVF RGB DRIVER, TIMING
GENERATOR, AUDIO I/O, A/D, D/A CONVERTER,
CHARGE SWITCH, DC/DC CONVERTER,
REGURATOR, CONNECTOR)
DV STILL/AUDIO DIGITAL STILL CONTROL,
DIGITAL STILL CONTROL, HI CONTROL, SDRAM/
FLASH MEMORY, DV SIGNAL PROCESSOR, RF
SIGNAL PROCESSOR, DV INTERFACE, REC/PB
AMP, VIDEO IN/OUT, AGC, CAPSTAN/DRUM/LD
MOTOR DRIVE, HI CONTROL, MECHA CONTROL,
CAMERA CONTROL, EVF RGB DRIVER, TIMING
GENERATOR, AUDIO I/O, A/D, D/A CONVERTER,
CHARGE SWITCH, DC/DC CONVERTER,
REGURATOR, CONNECTOR)
PRINTED WIRING BOARD ······················· 4-77
4-4.
WAVEFORMS ······························································ 4-85
4-5.
MOUNTED PARTS LOCATION ································· 4-89
5.
REPAIR PARTS LIST
5-2.
ELECTRICAL PARTS LIST ········································ 5-15
DCR-PC103E/PC104E/PC105/PC105E
COVER
COVER
Link
Link
4-2. SCHEMATIC DIAGRAMS
VC-319 BOARD (3/18)
(LENS DRIVE)
VC-319 BOARD (12/18)
(HI CONTROL)
VC-319 BOARD (16/18)
(CHARGE SWITCH)
VC-319 BOARD (18/18)
(CONNECTOR)
VC-319 BOARD (8/18)
(DV INTERFACE)
VC-319 BOARD (9/18)
(REC/PB AMP)
VC-319 BOARD (1/18)
(TIMING GENERATOR, S/H,AGC,A/D)
VC-319 BOARD (2/18)
(CAMERA PROCESS)
VC-319 BOARD (10/18)
(VIDEO IN/OUT,AGC)
VC-319 BOARD (6/18)
(SDRAM/FLASH MEMORY)
VC-319 BOARD (7/18)
(DV SIGNAL PROCESSOR, RF SIGNAL PROCESSOR)
VC-319 BOARD (11/18)
(CAPSTAN/DRUM/LD MOTOR DRIVE)
VC-319 BOARD (13/18)
(MECHA CONTROL, CAMERA CONTROL)
VC-319 BOARD (14/18)
(EVF RGB DRIVER, TIMING GENERATOR)
VC-319 BOARD (15/18)
(AUDIO I/O, A/D, D/A CONVERTER)
VC-319 BOARD (17/18)
(DC/DC CONVERTER, REGURATOR)
VC-319 BOARD (4/18)
(MPEG MOVIE/DV SIGNAL/AUDIO/DIGITAL STILL CONTROL)
VC-319 BOARD (5/18)
(DIGITAL STILL CONTROL,HI CONTROL)
VC-319 BOARD (3/18)
(
LENS DRIVE
)
VC-319 BOARD (12/18)
(
HI CONTROL
)
VC-319 BOARD (16/18)
(
CHARGE SWITCH
)
VC-319 BOARD (18/18)
(
CONNECTOR
)
VC-319 BOARD (8/18)
(
DV INTERFACE
)
VC-319 BOARD (9/18)
(
REC/PB AMP
)
VC-319 BOARD (1/18)
(
TIMING GENERATOR, S/H,AGC,A/D
)
VC-319 BOARD (2/18)
(
CAMERA PROCESS
)
VC-319 BOARD (10/18)
(
VIDEO IN/OUT,AGC
)
VC-319 BOARD (6/18)
(
SDRAM/FLASH MEMORY
)
VC-319 BOARD (7/18)
(
DV SIGNAL PROCESSOR, RF SIGNAL PROCESSOR
)
VC-319 BOARD (11/18)
(
CAPSTAN/DRUM/LD MOTOR DRIVE
)
VC-319 BOARD (13/18)
(
MECHA CONTROL, CAMERA CONTROL
)
VC-319 BOARD (14/18)
(
EVF RGB DRIVER, TIMING GENERATOR
)
VC-319 BOARD (15/18)
(
AUDIO I/O, A/D, D/A CONVERTER
)
VC-319 BOARD (17/18)
(
DC/DC CONVERTER, REGURATOR
)
VC-319 BOARD (4/18)
(
MPEG MOVIE/DV SIGNAL/AUDIO/DIGITAL STILL CONTROL
)
VC-319 BOARD (5/18)
(
DIGITAL STILL CONTROL,HI CONTROL
)
WAVEFORMS
COMMON NOTE FOR SCHEMATIC DIAGRAMS
WAVEFORMS
COMMON NOTE FOR SCHEMATIC DIAGRAMS
