Read Sony DCR-IP5E / DCR-IP7E Service Manual online
— 2 —
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
0
OR DOTTED LINE WITH
MARK
0
ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
1.
Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.
connections. Check the entire board surface for solder splashes
and bridges.
2.
Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
"pinched" or contact high-wattage resistors.
3.
Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
4.
Look for parts which, through functioning, show obvious signs
of deterioration. Point them out to the customer and
recommend their replacement.
of deterioration. Point them out to the customer and
recommend their replacement.
5.
Check the B+ voltage to see it is at the values specified.
6.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
DCR-IP5E/IP7E
DCR-IP5E
RMT-818
✕
✕
✕
✕
✕
✕
DCR-IP7E
RMT-817
a
a
a
a
Remark
a: with IC1601, 1602, 1605,
1606, 1801, 1802, 1803
of VC-263 board
a: with BT-003 board
Table for difference of functions
Model
Remote commander
Memory mode
Memory stick
USB connector
NETWORK (Bluetooth)
(BT-003 board)
(BT-003 board)
Battery pack
NP-FF50
NP-FF50
Maximum output voltage
DC 8.4 V
Output voltage
DC 7.2 V
Capacity
4.8 Wh (675 mAh)
Operating temperature
0
DC 8.4 V
Output voltage
DC 7.2 V
Capacity
4.8 Wh (675 mAh)
Operating temperature
0
°
C to 40
°
C (32
°
F to 104
°
F)
Dimensions (approx.)
40.8
40.8
×
12.5
×
49.1 mm
(1 5/8
×
1/2
×
1 15/16 in.)
(w/h/d)
Mass (approx.)
45 g (1.6 oz)
Type
Lithium ion
Mass (approx.)
45 g (1.6 oz)
Type
Lithium ion
“Memory Stick”
(DCR-IP7E only)
(DCR-IP7E only)
Memory
Flash memory
8 MB: MSA-8A
Operating voltage
2.7-3.6 V
Power consumption
Approx. 45 mA in the operating
mode
Approx. 130
Flash memory
8 MB: MSA-8A
Operating voltage
2.7-3.6 V
Power consumption
Approx. 45 mA in the operating
mode
Approx. 130
µ
A in the standby
mode
Dimensions (approx.)
50
Dimensions (approx.)
50
×
2.8
×
21.5 mm
(2
×
1/8
×
7/8 in.) (w/h/d)
Mass (approx.)
4 g (0.14 oz)
4 g (0.14 oz)
Design and specifications are
subject to change without notice.
subject to change without notice.
AC power adaptor
AC-L20A
AC-L20A
Power requirements
100 - 240 V AC, 50/60 Hz
Power consumption
23 W
Output voltage
DC OUT: 8.4 V, 1.5 A in the
operating mode
Operating temperature
0
100 - 240 V AC, 50/60 Hz
Power consumption
23 W
Output voltage
DC OUT: 8.4 V, 1.5 A in the
operating mode
Operating temperature
0
°
C to 40
°
C (32
°
F to 104
°
F)
Storage temperature
–20
–20
°
C to +60
°
C (–4
°
F to +140
°
F)
Dimensions (approx.)
125
125
×
39
×
62 mm
(5
×
1 9/16
×
2 1/2 in.) (w/h/d)
excluding (projecting parts) mains
lead
Mass (approx.)
280 g (9.8 oz)
excluding the mains lead
lead
Mass (approx.)
280 g (9.8 oz)
excluding the mains lead
Click on the first or last page to see other DCR-IP5E / DCR-IP7E service manuals if exist.