Read Sony DCR-HC51E / DCR-HC52 / DCR-HC52E / DCR-HC53E / DCR-HC54 / DCR-HC54E (serv.man4) Service Manual online
6-9
DCR-HC51E/HC52/HC52E/HC53E/HC54/HC54E_ADJ
1-2-1.
Initialization of A, D Page Data
Note: Check that the data of page: 0, address: 10 is “00”.
1.
Initializing of A, D Page Data
Note 1: If “Initialization of Pages A, D” is executed, all data on
pages A, D are initialized.
Note 2: If the A, D page data has been initialized, the following
adjustments need to be performed again.
1) Modification of A, D page data
2) Touch panel adjustment
1) Modification of A, D page data
2) Touch panel adjustment
Note 3: NTSC model: DCR-HC52/HC54
PAL model: DCR-HC51E/HC52E/HC53E/HC54E
Adjustment Page
A
Adjustment Address
10 to FF
Adjustment Page
D
Adjustment Address
10 to 7F
Initializing method:
Order Page Address Data
Procedure
1
0
01
01
2
0
10
00
3
7
03
Set the following data.
00: NTSC model
80: PAL model
80: PAL model
4
7
00
Set the following data.
20: Initializing A page
22: Initializing D page
28: Initializing A and D pages
22: Initializing D page
28: Initializing A and D pages
5
7
01
Set the following data, and
press PAUSE button.
press PAUSE button.
20: Initializing A page
22: Initializing D page
28: Initializing A and D pages
22: Initializing D page
28: Initializing A and D pages
6
7
02
Check the data changes to
“01”.
“01”.
7
Perform “Modification of A,
D Page Data”
D Page Data”
2.
Modification of A, D Page Data
If the A, D page data has been initialized, change the data of
the“Fixed data-2” address shown in the following table by manual
input.
the“Fixed data-2” address shown in the following table by manual
input.
Modifying method:
1) Before changing the data, select page: 0, address: 01, and set
1) Before changing the data, select page: 0, address: 01, and set
data: 01.
2) New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
the data built in the same model.
Note 1: If copy the data built in the different model, the
the data built in the same model.
Note 1: If copy the data built in the different model, the
camcorder may not operate.
3) When changing the data, press the PAUSE (Write) button of
the adjustment remote commander each time when setting new
data to write the data in the non-volatile memory.
data to write the data in the non-volatile memory.
4) Check that the data of adjustment addresses is the initial value.
If not, change the data to the initial value.
Processing after completing modification A, D page data:
Order Page Address Data
Procedure
1
2
00
29
2
2
01
29
Press PAUSE (Write) button.
Note 2: If the following symptoms occur after completing of
the“Modification A, D page data”, check that the data of
the “Fixed data-2” addresses of A, D page are same as
those of the same model of the same destination.
1) The power is shut off so that unit cannot operate.
the “Fixed data-2” addresses of A, D page are same as
those of the same model of the same destination.
1) The power is shut off so that unit cannot operate.
1-2.
INITIALIZATION OF 8, A, C, D, E, F, 1C, 1F
PAGE DATA
PAGE DATA
Note 1: If reading/writing data on pages 1C, 1F, set data: 01 to
page: 0, address: 10, and then select pages C, F. By this
data setting, the pages 1C, 1F can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
data setting, the pages 1C, 1F can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
Click on the first or last page to see other DCR-HC51E / DCR-HC52 / DCR-HC52E / DCR-HC53E / DCR-HC54 / DCR-HC54E (serv.man4) service manuals if exist.