Read Sony DCR-HC44E / DCR-HC46 / DCR-HC46E (serv.man11) Service Manual online
— 2 —
DCR-HC44E/HC46/HC46E_ADJ
• SWITCHING THE LENS BLOCK
(LSV-1080C
→ LSV-1080B)
For this set, the lens block was changed from the LSV-1080C to the
LSV-1080B in the middle of the production. When the lens block
or the VC-418 board is replaced, rewrite the data before adjustment
according to the type of lens block.
LSV-1080B in the middle of the production. When the lens block
or the VC-418 board is replaced, rewrite the data before adjustment
according to the type of lens block.
Type of lens block and part number
Discrimination method by LENS BLOCK
a) If the lens block is replaced
Check the marking B or C on the lens flexible board, and replace
the lens block with the same type.
the lens block with the same type.
b) If the VC-418 board is replaced
(lens block is not replaced)
Check the marking B or C on the lens flexible board, and rewrite
the data according to the type of lens block.
Check the marking B or C on the lens flexible board, and rewrite
the data according to the type of lens block.
Writing Method:
1) Select page: 0, address: 01 and set data: 01.
2) Select page: 0, address: 10 and set data: 01.
3) Select page: 1E, 1F, and enter the following data.
Note: Press the PAUSE (Write) button of the adjustment remote
1) Select page: 0, address: 01 and set data: 01.
2) Select page: 0, address: 10 and set data: 01.
3) Select page: 1E, 1F, and enter the following data.
Note: Press the PAUSE (Write) button of the adjustment remote
commander each time to set data.
4) Select page: 0, address: 10, and set data: 00.
5) Select page: 0, address: 01, and set data: 00.
5) Select page: 0, address: 01, and set data: 00.
c) Camera adjustment data after replacement of lens
block or VC-418 board
For “9. F. No & ND Light Quality Standard Data Input” and
“11. Mechanical Shutter Adjustment” in 6-1. CAMERA
SYSTEM ADJUSTMENTS of the Service Manual, use the data
selectively according to the lens used.
Note: The data must be input again if there is no pre-repair
For “9. F. No & ND Light Quality Standard Data Input” and
“11. Mechanical Shutter Adjustment” in 6-1. CAMERA
SYSTEM ADJUSTMENTS of the Service Manual, use the data
selectively according to the lens used.
Note: The data must be input again if there is no pre-repair
data when the VC-418 was replaced.
Lens block
Part No.
LSV-1080C
8-848-812-01
LSV-1080B
8-848-805-01
Marking
B : LSV-1080B
C : LSV-1080C
C : LSV-1080C
Data
Page
Addres
LSV-1080C
LSV-1080B
NTSC
PAL
NTSC
PAL
07
70
70
50
50
1E
08
A0
A0
80
80
A0
2A
2A
32
32
1F
40
3E
32
4E
3F
9.
F No. & ND Light Quality Standard Data Input
RadarW
RadarW
RadarW
RadarW
RadarW
(Service manual page 6-28)
Correct the lens iris and dispersion of the ND filter light quantity.
Correct the lens iris and dispersion of the ND filter light quantity.
Adjustment Page
F
Adjustment Address
1C to 23
Note 1: Check that the data of page: 0, address: 10 is “00”.
Adjusting method:
1) Select page: 0, address: 01, and set data: 01.
2) Input the following data to page: F, address: 1C to 23.
Note 2: Press the PAUSE (Write) button of the adjustment remote
1) Select page: 0, address: 01, and set data: 01.
2) Input the following data to page: F, address: 1C to 23.
Note 2: Press the PAUSE (Write) button of the adjustment remote
commander each time to set data.
3) Select page: 0, address: 01, and set data: 00.
Addres
Data
LSV-1080C
LSV-1080B
1C
F8
ED
1D
03
F5
1E
09
FB
1F
13
08
20
F1
0B
21
F8
F6
22
13
08
23
20
0F
: Points changed portion.
1-3. CAMERA SYSTEM ADJUSTMENTS
Click on the first or last page to see other DCR-HC44E / DCR-HC46 / DCR-HC46E (serv.man11) service manuals if exist.