Read Sony DCR-HC16E / DCR-HC18E / DCR-HC20 / DCR-HC20E Service Manual online
SERVICE MANUAL
LEVEL
3
Revision History
Revision History
How to use
Acrobat Reader
How to use
Acrobat Reader
DCR-HC16E/HC18E/
HC20/HC20E
RMT-830
Link
PRINTED WIRING BOARDS
REPAIR PARTS LIST
SCHEMATIC DIAGRAMS
PRINTED WIRING BOARDS
REPAIR PARTS LIST
SCHEMATIC DIAGRAMS
Link
The information that is not described in this Service Manual is described
in the LEVEL 2 Service Manual.
When repairing, use this manual together with LEVEL 2 Service Manual.
in the LEVEL 2 Service Manual.
When repairing, use this manual together with LEVEL 2 Service Manual.
Contents of LEVEL 2 Service Manual
1. SERVICE NOTE
2. DISASSEMBLY
2. DISASSEMBLY
3. BLOCK DIAGRAMS
4. PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS
5. REPAIR PARTS LIST
6. ADJUSTMENTS
OVERALL
POWER
CD-489, PD-213, LB-095, SE-141,
JK-260, IR-051, MS-200, FP-836
BOARD,
CONTROL KEY BLOCK
(SB6300, SS6300, CF6300)
FP-228, FP-467, FP-826, FP-830
FLEXIBLE BOARD
POWER
CD-489, PD-213, LB-095, SE-141,
JK-260, IR-051, MS-200, FP-836
BOARD,
CONTROL KEY BLOCK
(SB6300, SS6300, CF6300)
FP-228, FP-467, FP-826, FP-830
FLEXIBLE BOARD
EXPLODED VIEWS
ELECTRICAL PARTS LIST
ELECTRICAL PARTS LIST
• For INSTRUCTION MANUAL, refer to SERVICE MANUAL, LEVEL 1 (987670441.pdf).
• Reference number search on printed wiring boards is available.
Ver. 1.
5
2007. 09
DIGITAL VIDEO CAMERA RECORDER
Z MECHANISM (MDX-Z200)
Photo : DCR-HC20E
DCR-HC20
US Model
Canadian Model
Korea Model
DCR-HC16E/
HC18E/HC20E
AEP Model
East European Model
North European Model
DCR-HC18E/HC20E
UK Model
DCR-HC20/HC20E
E Model
Tourist Model
DCR-HC20E
Australian Model
Chinese Model
Hong Kong Model
— 2 —
DCR-HC16E/HC18E/HC20/HC20E
1.
Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.
connections. Check the entire board surface for solder splashes
and bridges.
2.
Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
"pinched" or contact high-wattage resistors.
3.
Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
4.
Look for parts which, through functioning, show obvious signs
of deterioration. Point them out to the customer and
recommend their replacement.
of deterioration. Point them out to the customer and
recommend their replacement.
5.
Check the B+ voltage to see it is at the values specified.
6.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
Unleaded solder
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40°C higher than
• Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
0
OR DOTTED LINE WITH
MARK
0
ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE
0
SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
CAUTION :
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
— 3 —
DCR-HC16E/HC18E/HC20/HC20E
TABLE OF CONTENTS
4.
PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS
SCHEMATIC DIAGRAMS
4-2.
SCHEMATIC DIAGRAMS
H• VC-350 (1/13) (TIMING GENERATOR, S/H, AGC,
ADC)
SCHEMATIC DIAGRAM ···························· 4-19
SCHEMATIC DIAGRAM ···························· 4-19
• VC-350 (2/13) (LENS DRIVE)
SCHEMATIC DIAGRAM ···························· 4-21
• VC-350 (3/13) (CAMERA/DV SIGNAL/AUDIO
PROCESSOR, DV INTERFACE, VIDEO OUT)
SCHEMATIC DIAGRAM ···························· 4-23
SCHEMATIC DIAGRAM ···························· 4-23
• VC-350 (4/13) (REC PB/AMP)
SCHEMATIC DIAGRAM ···························· 4-25
• VC-350 (5/13) (DRUM/CAPSTAN/LOADING
MOTOR DRIVE)
SCHEMATIC DIAGRAM ···························· 4-27
SCHEMATIC DIAGRAM ···························· 4-27
• VC-350 (6/13) (CAMERA/MECHCA CONTROL)
SCHEMATIC DIAGRAM ···························· 4-29
• VC-350 (7/13) (HI CONTROL)
SCHEMATIC DIAGRAM ···························· 4-31
• VC-350 (8/13) (RGB DRIVE)
SCHEMATIC DIAGRAM ···························· 4-33
• VC-350 (9/13) (D/A-A/D CONV., MIC AMP,
AUDIO OUT)
SCHEMATIC DIAGRAM ···························· 4-35
SCHEMATIC DIAGRAM ···························· 4-35
• VC-350 (10/13) (POWER IN, CHARGE)
SCHEMATIC DIAGRAM ···························· 4-37
• VC-350 (11/13) (DC/DC CONVERTER)
SCHEMATIC DIAGRAM ···························· 4-39
• VC-350 (12/13) (CONNECTOR-1)
SCHEMATIC DIAGRAM ···························· 4-41
• VC-350 (13/13) (CONNECTOR-2)
SCHEMATIC DIAGRAM ···························· 4-43
4-3.
PRINTED WIRING BOARDS
• VC-350 (TIMING GENERATOR, S/H, AGC, ADC,
LENS DRIVE, CAMERA/DV SIGNAL/AUDIO
PROCESSOR, DV INTERFACE, VIDEO OUT,
REC/PB AMP, DRUM/CAPSTAN/LOADING
MOTOR DRIVE, CAMERA/MECHA CON-
TROL, HI CONTROL, RGB DRIVE, D/A-A/D
CONV., MIC AMP, AUDIO OUT, POWER IN,
CHARGE, DC/DC CONVERTER, CONNEC-
TOR-1, CONNECTOR-2)
PRINTED WIRING BOARD ······················· 4-59
PROCESSOR, DV INTERFACE, VIDEO OUT,
REC/PB AMP, DRUM/CAPSTAN/LOADING
MOTOR DRIVE, CAMERA/MECHA CON-
TROL, HI CONTROL, RGB DRIVE, D/A-A/D
CONV., MIC AMP, AUDIO OUT, POWER IN,
CHARGE, DC/DC CONVERTER, CONNEC-
TOR-1, CONNECTOR-2)
PRINTED WIRING BOARD ······················· 4-59
4-4.
MOUNTED PARTS LOCATION ································· 4-67
5.
REPAIR PARTS LIST
5-2.
ELECTRICAL PARTS LIST ········································ 5-16
DCR-HC16E/HC18E/HC20/HC20E
VC-350 BOARD (7/13)
(HI CONTROL)
VC-350 BOARD (13/13)
(CONNECTOR-2)
VC-350 BOARD (9/13)
(D/A-A/D CONV., MIC AMP, AUDIO OUT)
VC-350 BOARD (3/13)
(CAMERA/DV SIGNAL/AUDIO PROCESSOR, DV INTERFACE, VIDEO OUT)
VC-350 BOARD (5/13)
(DRUM/CAPSTAN/LOADING MOTOR DRIVE)
VC-350 BOARD (6/13)
(CAMERA/MECHA CONTROL)
VC-350 BOARD (1/13)
(TIMING GENERATOR, S/H, AGC, ADC)
VC-350 BOARD (12/13)
(CONNECTOR-1)
VC-350 BOARD (11/13)
(DC/DC CONVERTER)
VC-350 BOARD (10/13)
(POWER IN, CHARGE)
VC-350 BOARD (8/13)
(RGB DRIVE)
VC-350 BOARD (2/13)
(LENS DRIVE)
VC-350 BOARD (4/13)
(REC/PB AMP)
VC-350 BOARD (7/13)
(HI CONTROL)
VC-350 BOARD (13/13)
(CONNECTOR-2)
VC-350 BOARD (9/13)
(D/A-A/D CONV., MIC AMP, AUDIO OUT)
VC-350 BOARD (3/13)
(CAMERA/DV SIGNAL/AUDIO PROCESSOR, DV INTERFACE, VIDEO OUT)
VC-350 BOARD (5/13)
(DRUM/CAPSTAN/LOADING MOTOR DRIVE)
VC-350 BOARD (6/13)
(CAMERA/MECHA CONTROL)
VC-350 BOARD (1/13)
(TIMING GENERATOR, S/H, AGC, ADC)
VC-350 BOARD (12/13)
(CONNECTOR-1)
VC-350 BOARD (11/13)
(DC/DC CONVERTER)
VC-350 BOARD (10/13)
(POWER IN, CHARGE)
VC-350 BOARD (8/13)
(RGB DRIVE)
VC-350 BOARD (2/13)
(LENS DRIVE)
VC-350 BOARD (4/13)
(REC/PB AMP)
COMMON NOTE FOR SCHEMATIC DIAGRAMS
COMMON NOTE FOR SCHEMATIC DIAGRAMS
4-2. SCHEMATIC DIAGRAMS
Link
Link
