Read Sony DCR-DVD505 / DCR-DVD505E / DCR-DVD905 / DCR-DVD905E (serv.man2) Service Manual online
1-3
DCR-DVD505/DVD505E/DVD905/DVD905E_L2
ENGLISH
JAPANESE
ENGLISH
JAPANESE
1-5-3. Self-diagnosis Code Table
C
C
C
C
C
C
E
E
E
E
E
E
E
E
E
E
E
Block
Function
0
4
1
3
1
3
2
1
3
2
3
2
2
0
3
1
4
0
4
0
6
1
6
1
6
2
6
2
9
1
9
4
9
4
Detailed
Code
0
0
0
0
0
2
0
0
5
0
6
0
0
0
0
0
0
0
0
1
1
0
1
1
0
0
0
1
0
1
0
0
0
1
-
Symptom/State
Non-standard battery is used.
Faulty disc is used.
Disc access error
Condensation.
Codec IC dose not return any reply
Difficult to adjust focus
(Cannot initialize focus)
(Cannot initialize focus)
EEPROM data are rewritten.
Drive fault
Codec IC fault
Audio Codec IC fault
Zoom operations fault
(Cannot initialize zoom lens.)
(Cannot initialize zoom lens.)
The abnormalities in initialization of
the focus lens and the abnormalities in
initialization of the zoom lens occurred
simultaneously.
the focus lens and the abnormalities in
initialization of the zoom lens occurred
simultaneously.
Handshake correction function does not
work well. (With PITCH angular
velocity sensor output stopped.)
work well. (With PITCH angular
velocity sensor output stopped.)
Handshake correction function does not
work well. (With YAW angular velocity
sensor output stopped.)
work well. (With YAW angular velocity
sensor output stopped.)
Abnormality when flash is being charged.
Fault of writing to or erasing the
flashmemory
flashmemory
Fault of writing to or erasing EEPROM
Self-diagnosis Code
Repaired b
y:
Correction
Use the InfoLITHIUM battery.
Use a compatible disc with the camcorder.
Clean the disc with the supplied cleaning cloth.
Use a compatible disc with the camcorder.
Use a compatible disc with the camcorder.
Remove the disc, and insert it again after one hour.
Remove the power source. Reconnect it again and operate your
camcorder again
camcorder again
Retry turn the power on by the power switch. If it does not
recover, check the focus MR sensor of lens block (pin ql, wa of
CN2101 on the VC-439 board). If it is OK, check the focus
motor drive IC (IC2104 on the VC-439 board).
recover, check the focus MR sensor of lens block (pin ql, wa of
CN2101 on the VC-439 board). If it is OK, check the focus
motor drive IC (IC2104 on the VC-439 board).
Make EEPROM data correct value. (Note 1)
Inspect or replacement of the mechanism deck, IC (IC4301 on
the MD-129 board) and drive block
the MD-129 board) and drive block
Inspect or replacement of the codec IC (IC3001on the VC-439
board) peripheral circuits
board) peripheral circuits
Inspect or replacement of the Audio Codec IC (IC3001 on the
VC-439 board) peripheral circuits
VC-439 board) peripheral circuits
Inspect the lens block zoom MR sensor (pin qh, qk of CN2101
on the VC-439 board) when zooming is performed when the
zoom lever is operated, and the zoom motor drive circuit
(IC2104 on the VC-439 board) when zooming is not performed.
on the VC-439 board) when zooming is performed when the
zoom lever is operated, and the zoom motor drive circuit
(IC2104 on the VC-439 board) when zooming is not performed.
Check both C: 32: 60 and E: 61: 10 of the self-diagnosis code.
Inspect PITCH angular velocity sensors (SE6801 on the CM-069
board) peripheral circuits.
board) peripheral circuits.
Inspect YAW angular velocity sensors (SE6802 on the CM-069
board) peripheral circuits.
board) peripheral circuits.
Checking of flash unit or replacement of flash unit. (Note 2)
Inspect the flash memory (IC3101 on the VC-439 board). (Note 1)
Inspect the EEPROM (IC2602 on the VC-439 board). (Note 1)
Note1:
Refer to “10-2. Record of Self-diagnosis check” of “3-5. SERVICE MODE”, ADJ (9-876-938-51).
Note2:
After repair, be sure to perform “1-6. PROCESS AFTER FIXING FLASH ERROR”.
Click on the first or last page to see other DCR-DVD505 / DCR-DVD505E / DCR-DVD905 / DCR-DVD905E (serv.man2) service manuals if exist.